Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
Hello,
i found a few articels about it but none of them where helpfull for me.
I just want to use my nRF51822 Module from Raytac without an external 32khz oszillator....
I was having an issue where reading from SPI inside a timer handler always yielded 0xFF instead of the actual values. I tried to reproduce the issue with a simple test program...
I'm trying to do a firmware update over BLE.
Here's what I did: - I created a new application from sample "smp_svr" because I think that is where I can see how to do firmware...
I'm running on Windows 10 and am trying to connect to my BMD-350 development board with an NRF52832.
I've also attempted to execute this with Python 3.9 and 3.8 (both installed...
I'm using SDK17.1 and pca10056 DK board. I want to use app_sched_event_put for a very simple purpose. I start a one second clock whose timeout handler increments a static...
Hi
I have configured my project to have a Modbus RTU slave on UART1. When I poll the dev kit, using Modscan, I get frame length errors. I have checked baud rate and parity...
I am trying to figure out why my application is generating a hard fault. The hardware platform is nRF52832 and SDK is 17.1.0
In my experience, the generic Cortex M3 processor...
We are trying to integrate the STEVAL_MODEM_BG96 chip into the NRF52840 for rapid prototyping. Trying to interface nrf52840 with the STEVAL-
STMODLTE chip via UART. Connecting...
I used to have a dts file for sdk52dk_nrf52832 containing gpio1 references:
rts: rts_pin{
status = "okay";
gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
label = "TS pin...
There was a question when doing the multi-channel test of ANT. The SDK is 17.1, and the example is (ant / ant_ multi_ channels)，Encountered the following problems：
1、Example...
I have
nRf52840 DK - 1 - Mesh Serail example nRF52840 Dongle - 2 - Mesh Light Switch Server example.
I used the steps given in the infocenter to provision and configure...
