I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello there,
I've set up a Thread network with a few devices, and now I would like to connect to a ipv4 server.
At home or at the office we do not have a ipv6 public address...
Hi,
We are Migrating from nRF52832 to nRF5340 dual-core soc. In nRF52832 9 off available GPIOs were only to use with a low drive, low-frequency application since they may...
I have starting working with UART. I see that there are two options for configuring it: UART_0_ASYNC and UART_0_INTERRUPT_DRIVEN. I want to use ASYNC option for my UART, but...
Hello
NCS1.8.0 Windows10 X64;
Can [v1.8.0\zephyr\tests\drivers\adc] convert microphone analog signal into digital signal? for I2S 8bit 8kHz
thanks
Best Regard...
Hi, I need to fetch the Device ID of nRF5340 Chip. In datasheet Info.DeviceID[n], n = 0...1 , is mentioned. How to access this information ? Also, I am using nTF5340-DK kit...
Hello
I am planning to purchase Nordic Semiconductor Power Profiler Kit. Before purchasing the kit I need to know, Is this kit supports another company's microcontrollers...
I am using nrf52832 with a custom board with no external crystal oscillator. As bootloader I use "secure_bootloader_uart_mbr" so I don't have softdevice. SDK is 17.1.0_ddde560...
using ble_app_interactive on one dev kit and connecting to pc viewing on terminal
other is my perihperal.
on entering connect <device address> it gets disconnected
hi I sucessfully tested the blinky project on the nRF52840 dongle... btw i'm using vanilla zephyr...
but i'm unable to prototype the uart comm on this board... the board...
I'm working on NCS 1.8.0.
I can use DFU APIs to upgrade my firmware successfully, however, after DFU is finished and system reboot, the McuBoot to swap images is too slow...
Hi, I want to know brief aboout difference and objective of different types of Zephyr projects. When using nRF Connect SDK, in SES a project is created, 3 options are available...
Hello,
I am using the nRF52840 DK board and writing code in Zephyr and I want to change the clock frequency. Currently, I guess by default it is 32.768KHz How can I change...
Hi,
I am using an nRF9160/nRFConnect SDK 1.8.0/VSCode and my application uses MCUBoot and SPM. It is a "non secure" application.
I am trying to get a reset cause.
hwinfo_get_reset_cause...
Hello,
We are developing a product based on the nrf52840 chip with our own antenna design. we would like to register our product in SIG and obtain a company identifier ID...
