I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am planning to create an application on NCS that can have https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bootloader using CONFIG_SECURE_BOOT=y, But is it possible...
TLDR; Need advice on which wireless communication protocol to use for five nRF52840 dongles within 75 feet of each other. I've never worked with Nordic Semiconductor products...
I'm experiencing an issue with I2C communication between the SEN5X sensor and multiple nRF9160 DK boards. The problem manifests as an crc error during I2C read operations...
In case I run the code from zephyr/samples/bluetooth/broadcast_audio_source, I get following error, when I play audio:
After I stop the audio, the log messages stop...
Hi,
I'm pretty new to Zephyr and I have to figure out how to connect to a NOR flash over SPI. Final application is the implementation of a file system, e.g. littlefs.
...
Hello !
I recently updated our project SDK from 2.6.0 to 2.7.0 and our custom board to HW v2 layout. Everything went almost seemless until I tried to enable sysbuild option...
We created a product using nrf52840. the product is operating well, but it has been confirmed that software reset (0x04) operates in very few times (2weeks per 1time). In...
I have a customised bootloader using uart + BL, built from the SDK examples and modified using articles found here. It works - most of the time. The product is a cusom board...
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hi,
We have previously realized the nRF7002 Matter project. We tried this with nRF52840. I am using Amazon Dot 4 but Amazon did not detect Matter. What is the reason for...
Hi:
I checked the zephyr.dts file, but why are the addresses for flash_controller: flash-controller@39000 and kmu: kmu@39000 the same? I checked the specification and 3900...
Hi,
One question, in VS code,
when I choose the nrf5340dk_nrf5340_cpuapp for build configuration, the VSCode told me the nrf5340dk_nrf5340_cpuapp is without security,...
Hi,
I get a very strange issue. Below is my device information:
NCS v2.4.0, Zephyr
It acts as a Peripheral
It advertises itself, accepting connection
Connection...
Hello, The following warning occures when I build the SLM Shell sample (Not changed original code).
[Build Configuration]
Target sample: SLM Shell ( https://docs.nordicsemi...