Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I've been struggling with this for some time now and no matter how I approach it I can't quite get it to work. I'm essentially looking for something like the "maximum performance...
Hello, I have several development-related questions about the microphone functionality of the NRF5340 AUDIO DK in headset mode:
Is it possible to configure the device...
I saw in this video that there was a lipo battery being used with a nrf52 Development Kit and I read this in the spec for the nrf5340 Development kit:
1.7-5.0 V supply...
Hi,
I am connecting a central to multiple peripherals. In order to optimize the throughput I would like to simultanuously sniff the connection. In the nrf Sniffer documentation...
We are producing an issue where the ZBOSS stack will emit a ZBOSS Fatal Error without any context if we alter ZB_DEV_REJOIN_TIMEOUT_MS. Specifically, the steps to reproduce...
Hello! I am trying to get gazell to work on the nrf52840 dongle.
I built the nrf connect sdk Blinky project with the nrf52840 dongle set as the config. then pushed the merged...
In the past, we've been able to use the nRF52-DK to flash our boards, supplying power through the debug port by shorting SB32.
For our L15 prototypes, the nRF52-DK doesn...
Hello Team,
I am experiencing an issue with the sound output from an external codec connected to the nRF5340 DK. Currently, the sound is in mono, but my goal is to achieve...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
NCS 2.7, nrf52840, sysbuild with mcuboot, multiple board revisions
I have setup my build to use different keys for each board revision with this in my sysbuild.conf:
...
Hello DevZone,
I just located a mysterious bug , it's about printk() and low power.
Environment:
NCS v2.8.0 and v2.9.0
nRF52840DK v3.0.2
PC: Ubuntu 22.04
Zephyr...
Hello. I am attempting to run the Matter Template app sample on the Adafruit Feather nRF52840 Express board.
I created a pm_static.yml file with the following configuration...
Hi,
I am using nrf52840 with nrfSDK-16.0, Ble5 coded PHY( S=8 ). I am using ESP32S3 as central and nrf52840 as peripheral device. I want to connect to 8 peripherals with...
When I try to program the Thingy:91 in cellular mode, it always gives the message 'Failed to connect to port.' I’ve tried different ports, but I get the same result.
