Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello All,
I am working on nrf52810 chipset and using SDK 17 for my development, I have modified BLE_HTS code by adding peripherals like I2C and ADC, I can able compile...
Hi, I am trying to use the BLE Direction Finding on the nRF52833 dK.
1. Are there any software examples I can use to help me get the direction finding running?
2. Also...
Hello,
I have created an application that collects data from sensors and GPS in two separate threads and publishes via MQTT. The two thread priorities are set to 10 and...
MIN and MAX macros are commonly defined in many code bases. These macros are also defined in nordic_common.h. To avoid conflicts with other libraries, it would be great if...
Hi, I have two pins, one handles a system wake-up event and the other reacts to an external uvlo event. The wake-up event is the only PIN that can interrupt and it configures...
Hello,
when I send notifications or indications to central device without bonding it works perfect. But after bonding they are not sent. I receive following logs when cetnral...
I am using nRF52840 dongle and nRF SDK version nRF5_SDK_17.0.0_9d13099.
When I am trying to debug the application it gives an error.
using your example project on nRF52840...
I can't go into too many details, but the scenario we have is:
We have an NRF52840 device connected to a PC through serial (for both power and communication) The NRF device...
I am trying to create a minimum working Keil uVision 5 S132 project with PCA100400. When I compare the examples with mine, I notice that during startup, when the code of flashed...
Hi
I heard in the "nRF Connect SDK" presentation from May 2020, that the nrfSDK only support BT 5.0.
Is this still correct that the features of BT5.1 and BT5.2 are not...
Hello,
I want to use RAM to keep some data after a soft reset, so that I can find problems after reset. And I also found some implementation methods, such as using .non_init...
Hi so I ran this example:
https://devzone.nordicsemi.com/f/nordic-q-a/40476/unable-to-convert-to-long-range-after-looking-at-umpteen-examples--/157426#157426
When I went...
I need BLE sniffer and I puchase this device because in this manual of "nRF Sniffer" say that "nRF52840 Development Kit (PCA10056) " is compatible.
https://infocenter...
Hi,
Looking at the footprint you supply for the aQFN73 package (I have looked at the one supplied for nRF52840), I see that the pad have a size = 0.275mm. If IPC-7351 is...
