I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi
I want to share how quickly start developing for NRF9160 with CLion, just in case someone tried and struggled, or someone really annoyed with Segger development experience...
Hi,
I am using nRF52 as a twi mater to read some data from a touch sensor, I want to perform below operation:
twi start
twi rx register_a for few bytes
repeated...
Dear Nordic team,
we have seen your announcement regarding BLE 5.2 audio: ( https://www.nordicsemi.com/News/2020/01/Nordic-launches-a-Bluetooth-LE-Audio-Evaluation-Platform...
Hi Nordic,
we are working on NRF9160_DK board ,we need to establish cloud connectivity but we are facing sim card network issue, we have activated sim card through 'nrfcloud...
I tried to download the firmware for nRF52DK , but almost emtly file was in the ZIP package. Only this file (12 kB): led_softblink_pca10040.hex
This certainly cannot be...
Hi,
I'm working on sending reliable message from server to client. It totally works fine if the message is less than 24 Bytes but then I got error when it's larger. The...
Hi, i am trying to add on_adv_evt in ble_app_beacon example. I modified sd_ble_gap_adv_set_configure(& m_adv_handle , &m_adv_data, &m_adv_params) to sd_ble_gap_adv_set_configure...
Hi, we are using nRF9160 and would like to save a data that is written only once(should not be overwritten or erased) and accessed every time it starts. I found that flash...
If LESC is not possible I'll settle for legacy.
I'm not able to find any document or sample code to help me get started. What i need is a pointer to document and hopefully...
Hi
I want to run the serial_uartes example for pca10040, are there any changes that i need to make in pca10056 config ? or will it work as it is in pca10056 ?
I am using...
Hi,
i am working with nRF52840-DK which i received yesterday from shipment. so i want to eun the BLE peripheral application on that.
As we know if we want to run the BLE...
I see this quote in response to a question asking for examples on how to code a scan response
possibly not - but it's trivial - just encode the scan response in the same...
Hello,
I am using SES V4.5, SDK 15.2 and the "ble_app_blinky_c" and I was not able to see the programme log.
I tried setting up the file "sdk_config.h" to use the RTT...
Hello,
I'm starting to develop an application using the DK pca10040 and SDK 15.3. At first I have just adapted peripheral ble_app_uart example and incorporated fds functionality...
