I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hi Earlier this week I got a mailshot from Nordic with the subject "Nordic Semiconductor’s nRF52840 System-on-Chip is now one of the first chips supporting Bluetooth LE with...
I have used the cli module in SDK 15.0.0 to create a test interface for a API I have built over UART. It works problem free when typing commands by hand but when automating...
Hi,
Look the nrf_mesh_rx_metadata_t definition:
typedef struct { nrf_mesh_rx_source_t source; /**< Source of the received packet. */ union { /** Scanner packet metadata...
Hi,
I'm eveluating the mesh SDK (with segger studio) for some days now and I can not stand that I still can't figure out what the examples for BLE mesh can and can't do...
Hi,
I'm in the middle of developing a software that runs on nRF52840 and scans for BLE devices all of the time, then quickly connects to each and every one as fast as possible...
We're using a host PC to write factory calibration data to an nrf52 running SDK14.0.0 and S132. We're using a serial port, 115200 8N1, without hardware handshaking. The SD...
Hello,
very simple question:
each time i click on the link from the following page, I get an ACCESS DENIED error
infocenter.nordicsemi.com/index.jsp
I know that...
I made some changes in mesh light_switch_client example code and tried to build it in SES, it passed compiling, but stucked at linking:
Building ‘light_switch_client_nrf52832_xxAA_s132_6...
hi..
i merged the two programs twi sensor and uart ... successfully complied
but while debugging i am getting this error
while (m_xfer_done == false)
lm75_mode();...
Hello all,
I have a question about the SAADC of nRF52832.
Now I use the SAADC to measure the some external sensor voltage and the internal VDD voltage.
The sensor connection...
Hello, Excuse me! I used the LFRC,the calibration interval of which is 8s, in my application on NRF52832. In order to measure the power consumption,I want to know the duartion...
Hi,
As well know, nRF52832 can use "16Mhz base-clock to output PWM signal, and it is very simple to create 4Mhz, 2Mhz, 1MHz signal output,
But, If I want to output a...
I'm trying to get a stripped down, simple LED blinking sample to work (like blinky) when building with GCC however main() is never called. I'm guessing I'm either using the...
I'm trying to take a project we had working with only an application, no softdevice or bootloader, and add a bootloader and softdevice, with the application still not requiring...
I am working on nrf5_SDK_for_Mesh_v2.2.0 with nRF5_SDK_15.0.0 and softdevice 6.0.0. I run code on PCA10040 dev boards. I am trying use a timer to send onoff message from a...
