Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I have a custom board on which I am running the fatfs example from SDK15.2.
On SD Card Initialisation the CMD0 response is unexpected: -
Where the NCR would be expected...
Hello-
We are preparing a product for Bluetooth certification. Our design has a PCB antenna and the the testing house is requiring an SMA RF coaxial cable to interface...
I have created a custom Board Support file for my custom Board But it is not able to advertise the BLE Device after I use My custom Board File. When I use Predefined board...
Hi,
We need to collect sensor data from nrf52832 and after some processing, we plot data and generate some notifications etc. on smartphone app.
Shortly we need to design...
Hello, I'm developing a solution by using MESH SDK : nrf5_SDK_for_Mesh_v2.1.1
There is an ASSERT on access.c in nrf5_SDK_for_Mesh_v2.1.1_src\mesh\access\src\ as below. ...
SoftDevice: S132_5.1.0
Environment: I have 1 Device Advertising and about 200 "tags" waking up every 10 seconds and scanning for those advertisements and connecting, I have...
HCI for NRF52840
Hello
I m using a STM32 + NRF52840 and i have a mbed project in my STM32 and i want to use The NRF52840 only as a Bluetooth component, is there an example...
Hi guys,
I compiled the openbootloader example and when I try to run it on NRF52840, It gives segmentation fault:
(gdb) load nrf52840_xxaa_debug.hex Loading section .sec1...
Hi,
I'm having problem with the example code in the "Bluetooth low energy Services, a beginner's tutorial", the code was downloaded from github.
I'm using SES V3.5 for...
Hi,
We are currently develop our costum board with an nRF52840 SoC. Are the nRF52840 shipped with an initial bootloader to programm the device via USB? Because if possible...
Hello folks.
Easy question.
I want to add a .a static library to Segger Studio, but I don't know exactly where to add it. I know how to do in a Makefile with GCC, same...
I found the reference design files for nRF24LE1 from here ( https://www.nordicsemi.com/eng/nordic/download_resource/10898/2/41030525/1871 ), but I can't open them in EAGLE...
pca10059, replacing stock bootloader with Adafruit UF2, using USB dfu Hi. I currently don't have a J-Link at hand, so I tried to flash the UF2 bootloader using the stock DFU...
I want to keep both chip antenna and external antenna options on our board, what is best way to handle this for nRF24LE1 4×4mm QFN24 chip-set? Can I branch the Radio by having...
Hi,
I have a nRF52840 DK and a nRF52840 Dongle. I want to test to send binary data from one to each other using Bluetooth 5 or Nordic proprietary protocols. Are there...
