Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
I was beyond excited to see all the support Nordic was providing to the mbedOS project.
All of a sudden it disappeared.
If not supporting mbed the alternatives would...
Hello,
We have an nrf51822 system where disconnecting the battery is problematic, and the sharing of the reset line between SWD and reset function has been a real source...
Hi. I'm beginner of nRF.
I want to get some data from a temperature sensor, but I don't know how to assign a pin. Also, how can I check the data ??
In Arduino, there...
Hello,
I'm attempting to include the "arm_math.h" library so that I can use the requisite DSP functions, etc. I'm getting a linker error so I'm not sure what else needs...
HI,
I am using nRF52832 and SDK 14.2 and trying to send MPU accelerometer values to android device through BLE . But when I call " mpu_init() " in main function to initiate...
Dear Sir,
I am new to Nordic. This is my first query. It is related to running Timer with softdevice. I am using TIMER1 ( as const nrf_drv_timer_t TIMER_LED = NRF_DRV_TIMER_INSTANCE...
Hi, Support team,
When I use the SPI peripheral communicate with nrf24l01+,it's no data return in m_rx_buf by using the API nrf_drv_spi_transfer(&spi,m_tx_buf,1, m_rx_buf...
Hi,
I use the FDS on our project firmware. The firmware saves some configurations to FDS at shutdown and the factory reset. At this time, sometime fds_gc() does not call...
Sometime, the timer handler is not call immediately after calling app_timer_start().
environment - nrf52840 - SDK 15 - with FreeRTOS - timer task priority is higher - timeout_ticks...
Hi,
In the nRF Mesh mobile app, when you go to the settings tab, you can hit "Reset Network", this appears to clear any previously provisioned network, and lets you start...
Hi all!
We've been time-stamping GPIO events using PPI in nRF52 , and it works* !
...but when using the SoftDevice , it apparently clashes with the PPI about 30ms after...
Hello,
I have been having issues when using the UART libraries (app_uart.h) with certain pins on the nrf52832. Previous iterations of our project have worked correctly but...
I am investigating an H4 HCI over a UART implementation for a client which plans to use the 52832 (or 52840) as a replacement for a TI BLE chip in a new design.
I have built...
Hi all
We are using customized board with nRf52810 chipset.
Actual requirement in our project is to send 100 bytes of data for 10 millisecond.
Kindly suggest a procedure...
