Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
I am using pca10028 and sdk12.2. I am trying to take sensor reading via TWI and I want to send this reading over ble. So I am trying to add twi files in ble_app_template...
I am attempting to increase the queue size for handle value notifications to support a higher number of packets per connection event. However, I am unable to set the queue...
Hello,
I'm working on nRF52832-DK with SDK11 on linux.
Is there an example to use whitelisting ? I'm trying to use HIDS_Mouse but it's not working.
How can I write...
i have learn how to program nRF51 DK with and without softdevice. Now i want design code as per my requirement... but find difficulty to understand given sequence of code...
Hi,
I am working over nrf51822 ble and I have some security issues with that. I'm programming an android app to connect to the nRF51822 (peripheral). Without any security...
Hi.
I'm trying to control a keyboard and a mouse with nRF24LU1+ USB dongle module.
www.nordicsemi.com/.../nRF24LU1P
I downloaded this link below from the Nordic website...
1\select zip file
2\scan and select nrf51 dev
3\upload.
then the nrf51 enter dfu mode, and can scan the dfutag ble dev. but the ADDR auto add 1 . Wait about 10 seconds...
Hello everyone.
I've got the nRF51822 Evaluation Kit and Dongle. The heartbeat demo is working, so I got the toolchain -- Nordic, Keil, Segger under Win7 -- set up correctly...
Hie,
Is it compulsary for us to send only 20 bytes of data or less than that in one packet in BT5 as we used to do it in BT4 to make BT5 compatible in communicating with...
Hi,
I want to develop a product with Bluetooth 5( NRF52840) capability, before starting development I wanted to know will the Bluetooth 5 devices(Peripheral) will be compatible...
Hi. When i use ble_app_uart i have problem with my device over uart. It does not response to my commands.
I'm using custom pcb based on nrf52 with nrf UART v2.0 android...
I have moved on to SDK12. But one old project using SDK10 now requires a 128 bit UUID.
I keep getting hard fault when I add UUID.
I noticed that there is no vs_uuid_count...
Hi Team,
I am using nRF5_SDK_11.0.0_freertos_dfu_060516.zip SDK. I have added NUS service with UART configurations in this code successfully.
When I am commented the DFU...
We have both nrf51 and nrf52 running DFU.
How can I identify on the mobile application side whether I'm connecting to nrf51 or nrf52?
They will need to get different firmware...
Hi,
Is it possible to know which type of advertising packet is being advertised by the slave i.e whether it is a connectable or a non connectable advertising packet by...
