Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
Recently updated to SDK11 + s130 v2.0.1 on an nRF51822 xxAC LFCLKSRC=RC
BLE Advertising no longer works. Localized it to our use of TIMER2 for an implementation of systick...
Hi,
Im trying to connect MCP25625 via SPI on nrf52. I checked with the scope that CS, MOSI and SCK are correct, but I get no reply on MISO line whatsoever.
I perform a...
Every time I want to connect to Nordic ble device from my Phone, it ask for pairing confirmation and then it create bond. That's how it should be.
But if the device is...
I'm using nfr52 with softdevice s132.
I want quickly perform flash write during power loss.
When I realize write using fs_store() I obtain time more than 5 msec.
How can...
Just do
NRF_POWER->SYSTEMOFF = 1;
in main()
and found if it's boot by powerup
the current is 10.4uA~10.5uA
and if a re-flash the hex, the current is 1.4~1.5uA
...
Hi,
Everyone,
I am using NRF51422 chip for my custom board. with transmission interval set to 2000ms and Tx power to -20 dBm, I transmit 32 Bytes BLE data and Scan and...
I use the softdevice which is s130.The code is from the demo:
static void nus_data_handler(ble_nus_t * p_nus, uint8_t * p_data, uint16_t length)
{
for (uint32_t i =...
Hi,
i'm using SPI to transfer data divided into packets of 24 bit from NRF51 to a DAC. The function that allows to send data is:
spi_master_send_recv(SPI_MASTER_1, data_vector_tx...
I'm having trouble starting my application after power cycling after flashing it with the DFU app.
I started nRFgo Studio. Erased the chip. Programmed the SoftDevice (s130_nrf51_2...
I was just wondering if anyone has any experience with or thoughs about using Zephyr ( www.zephyrproject.org/) or Mynewt ( http://mynewt.apache.org/) that they would like...
Hello all,
i am struggling with the example code of the Enhanced ShockBurst Protocoll in SDK 11. I cannot really see the structure of the code, to which time which event...
Hi all, in the forum I can read about people having issues with wrong CRC in the bootloader, but with SDK11; I have the opposite problem. It is always 0 and is always accepted...
main.c Hi,
I am having an issue with I2C transaction in my program.
There are two sensors(Touch and Temp) connected to the I2C bus. Touch sensor is working well when...
According to the official tutorial must before the MCU is powered on hold button 4 to enter DFU mode, detected that I how to achieve a certain GPIO port high level into DFU...
