Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I want to use app(nrf uart 2.0)
so, I try to change UUID,
but I don't know how make custom uuid and use it
and I don't find function(ble_cs_init())
hlep me, p...
I just tried compiling this for the BLE nano and it explodes to a 245K download (much too large for device). I've also tried including only the headers (DigitalOut and wait...
Hi,
I purchased Nordic new reference platform nRF51-DK(pca10028) and try to work for DFU OTA.
In my test, first of all program S110 V7.1.0 by nRFgoStudio and downloads bootloader...
Hi
In a bit of an over-enthousiastic mood, I bought 3 pieces of the nrf51822 beacon kit, and the, as this did not gave me download access to the NRF51 SDK, bought a nRF51...
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
Hello
Where can I find operating characteristics of pstorage_store and pstorage_update?
Actually, I observe that about 100 ms are needed to update 4 bytes data. For...
Hi All,
I have two application modules which will use the flash , 1) Bond manager 2) configuration file
I have register both modules with different parameter in the initialization...
keil 5.12 could install pack file. I'd like to install S130 0.9 to keil 5.12, but I did not find S130 0.9 pack file. Could I install S130 0.9 manually and could select the...
