I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi, what I did is wrote below:
1/ I program the S120 softdevice to the nRF51822 board, using nRFgo studio software(the softdevice size is set to 80KB).
2/ I complied the...
Hello,
I recently tested the nRF51822 with a non-Nordic BLE devices and encountered some problems. When testing with Nordic the connection is maintained with no problem...
During testing I changed the device name in the DFU. After making the change the DFU client in the master control panel would no longer work.
Is it possible to make the...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I try to configure a ppi channel with timers to generate pwm signal
My entire code is working well without softdevice.
Here my ppi init function:
NRF_PPI->CH[0...
I am planning to build mobile devices that communicate directly between them with BLE. The devices are all the same and carried by users. users meet and exchange data. I can...
hi,all!
i am confused about whicn priority should i set for my interrupt.
For deteils, I need a gpioe interrupt for my button, and this button is used to POWER OFF my...
We wish to make a universal device that may used
for ANT with the nrf51422 and the 32kHz crystal.
or for BLE with the nrf51822 without the 32kHz crystal.
Will there be...
I'm trying to bring up a basic S120 application on PCA10001 based on the multilink central example, using the IAR toolchain.
I've programmed the S120 device using 1.0.0_3...
I'm developing a next generation device using nrf51822. To replicate existing behavior I'm trying to sniff the previous generation product behavior using the ble sniffer on...
Hello!
I am working with a NRF51822 and I need to change the address of pipes regularly (so I can use more than 8 NRF communicating together with ESB protocol).
My problem...
Hi,
I'm trying to understand if S120 soft device provides user configurable option for duplicate filtering of advertisement data. I couldn't find any info on the SoftDevice...
Hi,
I used the project gzll_ack_payload in nRF51 SDK for nRF51822, I changed the Device to send a packet per second, every thing goes OK with the default parameter.
...
Hi,
there is an example named gzll_ack_payload in the SDK of nrf51822.
when nrf51822 works in device mode, if a packet is send successfully, the funciton of nrf_gzll_device_tx_success...
