Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
TLDR; Need advice on which wireless communication protocol to use for five nRF52840 dongles within 75 feet of each other. I've never worked with Nordic Semiconductor products...
I'm experiencing an issue with I2C communication between the SEN5X sensor and multiple nRF9160 DK boards. The problem manifests as an crc error during I2C read operations...
In case I run the code from zephyr/samples/bluetooth/broadcast_audio_source, I get following error, when I play audio:
After I stop the audio, the log messages stop...
Hi,
I'm pretty new to Zephyr and I have to figure out how to connect to a NOR flash over SPI. Final application is the implementation of a file system, e.g. littlefs.
...
Hello !
I recently updated our project SDK from 2.6.0 to 2.7.0 and our custom board to HW v2 layout. Everything went almost seemless until I tried to enable sysbuild option...
We created a product using nrf52840. the product is operating well, but it has been confirmed that software reset (0x04) operates in very few times (2weeks per 1time). In...
Hi Nordic Team,
I am currently developing applications for custom boards using the nRF Connect SDK v2.6.0, focusing on the nRF52840 microcontroller.
In our ongoing project...
Hi,
We have previously realized the nRF7002 Matter project. We tried this with nRF52840. I am using Amazon Dot 4 but Amazon did not detect Matter. What is the reason for...
Hi:
I checked the zephyr.dts file, but why are the addresses for flash_controller: flash-controller@39000 and kmu: kmu@39000 the same? I checked the specification and 3900...
Hi,
One question, in VS code,
when I choose the nrf5340dk_nrf5340_cpuapp for build configuration, the VSCode told me the nrf5340dk_nrf5340_cpuapp is without security,...
Hi,
I get a very strange issue. Below is my device information:
NCS v2.4.0, Zephyr
It acts as a Peripheral
It advertises itself, accepting connection
Connection...
Hello, The following warning occures when I build the SLM Shell sample (Not changed original code).
[Build Configuration]
Target sample: SLM Shell ( https://docs.nordicsemi...
Hi Support Team
We test the AoA sample of direction_finding_central and direction_finding_peripheral in the NCS of V2.4.0,and it has an issue of disconnected like the screenshot...
Hi, I have been using nordic nrf5340 in vscode(no sdk). I have taken ble throughput example code. I could able to connect in nrf connect app(phone) and i am able to read and...