Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi,
Using Visual Studio Code, when I build asset_tracker_v2 in NCS v2.9.1, for nrf9160dk/nrf9160.ns, I keep getting the problem shown in the subject line
equivalently...
I have been trying to:
add MCUBOOT and FOTA to a custom BLE board using the nRF54L15.
I had thought that the sole issue was that the custom board does not utilize...
Hello, I have a minor problem with starting up i2c0 and i2c1. I am trying to run a scanner in the sample code that will print out the addresses connected to these buses. I...
Hi,
I would like to know the best method to force a Public Land Mobile Network Identifier (PLMN). When working with an MVNO , it is very common not to get the right timers...
Hello,
I’m using the GNSS sample (located at C:\ncs\v2.9.0\nrf\samples\cellular\gnss ) to evaluate the GNSS module on our custom PCB, and I need to view its output over...
i am writing an absolutely minimal "bare-metal" application for the nRF54L05 -- one that doesn't use the zephyr kernel or drivers....
all i really need at this time are...
I am trying to use uart21 on nrf54L15-PDK. And I have try some port 1 pins already, and they works well. However, we need to use port2 pin 7 & pin 8 for uart21. But I get...
In my project I am facing issues to send 6000 bytes per second through BLE to androis app
For reading the sensor it is taking 30-40 ms processing time and after that I am...
Hello all, I'm getting stuck on re-installing any SDK and I'm getting the below error. The error:
Failed to clone the repositories: Error: HEAD is now at 100befc70c7 [nrf...
This would be a continuation from a previous discussion on the topic of Bonding information and the process of bonding between the peripheral aka headset and central device...
I am using nRF52 based NINA-112b EVK I saw the spi master example to send the data to slave. Do you have any idea what to do if I want to receive the data from the slave....
I am getting an error
warning: SPI_NOR (defined at soc/gaisler/gr716a/Kconfig.defconfig:18, drivers/flash/Kconfig.nor:6) was assigned the value 'y' but got the value ...
Hello, I need your help about BLE channels. Currently, I use only the primary channel 38 for advertising data but, when the data are sent, I don't have the information of...
Hello,
For a month I have been trying to find a solution to update my devices which are at my customers (these devices have a bootloader, softdevice and app coming from...
Hi
ncs 2.6.1 / toolchain 2.7.0
we have developed a Product using ANNA-B402 (with nRF52833).
Now we made a product variant with nRF52833 WLCSP. Both use the same application...
