Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
If you are interested I would to contribute to https://github.com/NordicSemiconductor/nRF-Sniffer-for-802.15.4 repository. On the python driver part. You could allow...
Hello
I'm doing a test that if it's possible to start ibeacon function when BLE is connected in nRF52840. so I merge ibeacon into HRM demo code and as you can in the following...
Hello ...
Our BLE peripheral product (nRF52810, SDK 15.3.0, SD 112 6.1.1) is relatively simple. iOS device (central) connects to peripheral. Data is exchanged between the...
Hi, i'm new to Nordic devices and i hope this topic hasn't already been treated. I'm triyng to debug an example application; after the first breakpoint, i loose the control...
Hi,
I try to set the TX power of the NRF52833 to the maximum possible power level, but somehow nothing seems to affect it.
I first tried to change it in the sdk_config...
In spec, 9160's PSM current is 4uA/3.7V.
However, When I use a same PSM code.
On our product. We measured is 4.5uA/3.7V and 5.5uA/3.7V. And on 9160DK, the consumption...
HI,
I'm trying to add some functions to my code, and the buttons interaction is one of them. I saw some posts and I think I did exactly like that but I can't get interaction...
So I was following the documentation. Installed everything successfully. And now I am trying to send the program to the nrf52840. However when I do ninja flash<program> I...
I've been trying to create a simple SPI to UART bridge starting with the peripheral template example from the nRF5 SDK 16. I want to read 5 bytes from uart, send them via...
I've reviewed the different PWM examples that include the low power PWM, PWM driver and the PWM library. What I'm looking for is a very simple solution to drive a bipolar...
Hi,
I'm wondering if the current nRF sniffer firmware (v3.0.0) can detect extended advertisements on arbitrary channels? Is it supported in the firmware? If so, can I use...
Hi all,
I did not do mesh SDK for a long time. Now when I see SDK Mesh, I saw Low power Node example. It can run with Mesh network and update OTA by DFU buttonless (I don...
Hi,
I had an experience with embedded programming but never with wireless technology. I am using Nordic SDK v16.0.0 and nRF Mesh SDK v4.0.0.
Here is a short description...
Hello All,
I am working on the Nrf52810 board with sdk 14.2.
I have implemented the read ,write , delete feature in my code.
Now it is creating new entry for repeating...
Dear All, I am trying to compile an application based on the Zephyr project for the nrf52. I am following the instructions from here .
I am using Windows. Using SES everything...
