Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
I have successfully compiled BLE application using tutorials provided on nordic website.
but when I start doing debugging for better understanding find out that I can not...
Hey,
We got a problem when trying to figure out how to detect the custom services from Unity. We are trying to read data and afterwards to do some manipulations of objects...
I want send ble bond connection request from raspberry pi to nrf51882.
Can you please let me know which ble libraries I need to send central ble bond request to nrf51882...
Dear Nordic:
I try to use pca10040 DK and SDK is nRF52_SDK_0.9.2_dbc28c9.
Test nRF52_SDK_0.9.2_dbc28c9\examples\peripheral\UART the function work well on my DK.
I...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
hi...........
i am using nrf52832 and a peripheral device . i have merged two programs uart and twi sensor . i am getting the data everything is fine , but after the few...
Using Rigado board, MBD350, I am able to write and test basic application using UART and BLE
using my custome board I get the following error:
NRF_BREAKPOINT_COND; ...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
I'm using an old version of the nRF5 SDK (v11.0.0, SoftDevice v2) as supported by the SparkFun nRF52832 breakout board and the Arduino BLEPeripheral library.
Having set...
I am using nrf52 DK and sdk 15.0.
I want to know whether we can transfer the file over the BLE or not?
I am using ble_app_uart example,Is there any possibility to modify...
