Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
So I'm constantly reading data using i2c into a variable. How do I transfer the data in this variable to the pc? It's just an array.
I understand that I have...
I am looking for a smallest size transceiver with an antenna done as part of the PCB layout (no external antenna needed). The simplest RF PCB layout is preferred, single frequency...
Hi, I purchased a Sparkfun Breakout board for the NRF52832, but the bootloader on it seems to be extremely unstable. Hence, I've decided to flash the NRF52832 directly from...
Hello,
I already checked below link, but want to clarify the limitations of how many concurrent sessions are allowed in Soft Device initialize.
devzone.nordicsemi.com...
Hello,
i add a new custom service with one characteristic that allows me to send values over BLE with nRF connect, but i must send some acceptable values (-2, -4, 0, 4, 10...
Using SDK14.0.0, nRF52832, GCC, GDB/Ozone, secure DFU
This question seems to get close to asking about my problem.
I am trying to debug my application with a loaded...
Hi,
We made a custom PCB using the NRF52832 and followed the reference design. While everything else is working in our system, the BLE part is not working. We are using...
Hello,
I try to develop an application on a nRF51802 device. But this device is not managed in nRF_Drivers.4.0.0-2.alpha.pack from Keil software.
Is there an update...
Hey guys! Like the title says, I'm looking for the best way to send values like humidity and VOC from the Nordic Thingy to the cloud. I have already set up the thingy to send...
Does anyone know of an off-the-shelf hardware and software that will let me read and write nRF52832 devices that are using the NFC Type 4 Library? We've tried the ACS ACR1252...
Materials publicly available say the chip works from 3.1 volts.
But is this the absolute minimum voltage or will it be possible to use also LiFePO4 battery cells with the...
I'm trying to set PWR_UP bit to 1 for the device to go into standby-I mode using STM32F103RBT6 and HAL libraries.
I send (0x20 | 0x00) command (write_reg | config reg)...
I'm trying to compile the S332 example project ble_ant_app_hrm_pca10040_s332.uvprojx. I'm using the V12 SDK and Keil uVision V5. When I try to compile I get an error saying...
Starting with "Development with GCC and Eclipse", I've gotten "blinky" to run on my BLE400 with an nrf58122 using Eclipse Oxygen. I think I'm using SDK12.3 . I started with...
