Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am facing the same issue regarding to this post "Custom Service Issue - devzone.nordicsemi.com/.../".
At least i could figure out the IRAM1 start and size as explained...
Hi there!
I have been working with serializer and have the below issue:
I am using sd_ble_gatts_hvx() to transfer 20 bytes in burst until I get an error (TX buffer full...
Hi all,
first I have to admit that I'm a total rookie in "electricity". I know BLE software-side but just started to learn the hardware stuff.
I just received my PPK and...
by writing servals data into flash ,the data is always is 0,
void fstorage_test(void)
{
ret_code_t ret = fs_init();
if (ret != NRF_SUCCESS)
{
bsp_indication_set...
HI,
I am using nrf52832 with softdevice 132. Using SPIS1 to get the sensor datas from nrf to AARDVARK for calibration. Whenever I send the data's from aardvark(using AArdvark...
Whenever I try to flash the device in keil, I get a no Jlink device found. I get a similar message when trying to connect to the device via Segger. nrfGo Studio just does...
hello:
i want to use pwm in SDK9.0, in my project ,i need to send a cmd to nrf51822-QFAA,and then it control the motor on ,and with this cmd ,i should contrl pwm to let...
Can I control the music player by simulate a hid device
now our customer ask for a new function--use bracelet control the music player>> last next vol+- ...
but the app...
Hi,
I am trying to develop the ble_app_template project into a custom ble application.
Where is says
/* YOUR_JOB: Declare all services structure you application is...
Hi Dear Engineers!
I use nRF52840 SPI (slave) to communicate with Master (HOST) CPU.
if I stop any ADV / SCAN RF functions all works Great!
But if I start ADV (or...
Hi,
I am having some trouble in setting up the RedBearLab BLE board w/ nRF51822 that i recently bought for a project I am currently doing . I am using windows OS, with eclipse...
Folks,
Attempting to use a sample app from the 13.0.0 SDK for a pointing (mouse) device I'm prototyping, located at ...\nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral...
I use the sdk 13.0.0,software device s332，I hope the rtc can work when cpu sleep,and the lowest working current need less than 10uA，what should i do？or Is there a reference...
