I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I'm trying to program Sparkfun nRF52832 board using SWD (via nRF52 DK). I've erased original bootloader/softdevice/app and programmed S132 and my app. The app works, but only...
Hello,
I'm beginner for NRF51822. I have tried ble_app_hids_keyboard example on NRF51822 with s130 softdevice.
It is discoverable in smartphone as Nordic_Keyboard. Smartphone...
We have been using the DFU that came with the sdk 12.1 with a modification (essentially removing the button from the DFU code). We currently send an application command that...
Hardware:
I have an nRF52 device running the S132 running as a Central.
I have 6 iOS/Android devices running as peripherals.
Background:
I am attempting to have my central...
Hello,
is there any good example available, with whom I can simulate, that there are two devices are already connected and the host is scanning for some other devices?...
I am trying to use the function or any function with my BLE UART application. I have a timer that expires to kickoff reading of some sensors and then when I try to read my...
Hi all,
i m connect a sensor with Nrf51822 beacon and get the data.
so i want to transfer those data to Nrf51 dk kit continuously.
where i want to change or put my data...
Hi,
I use nRF51422 in Dual mode(SD310) with SDK10 Version.
The profile is CSCS.
I want to ask
How to just show Speed Sensor or Cadence Sensor.
Here is what I did just...
Hello,
I'm evaluating the feasibility of using the nRF52832 chip on a board with a microprocessor running Android and I like to know if Nordic has released or is planning...
I'm using SDK nRF5_SDK_13.0.0_04a0bfd and compiling the example ble_peripheral/ble_app_hrs/pca10056/s140/armgcc using Eclipse Mars 2.
Flashing softdevice s140_nrf52840_5...
Dear Nordic.
I cant found stack API documentation for study.
All company give it for user, for example TI.
User open doc folder and can reed API.pdf file.
Where your...
I use NRF51822_xxaa, sdk12.2, arm_gcc 4.9_2015q3
when i flash hex file experimental_ble_app_blinky_pca10028_s130.hex from C:\NRF\SDK_12.2.0\examples\ble_peripheral\experimental_ble_app_blinky...
Hi,
i have NRF51822 beacon(PCA20006) and NRF51dk KIT(PCA10028).
I am connect a touch sensor and it's gives output in form of "HIGH & LOW".
and i am able to detect the output...
hi,
i want to connect sensor to nrf51822 to send data to smart app continuously over ble.i want to modify example ble_app_beacon. which functions i need to change?
