Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
Dear all:
error occured when I was programming application hex in nRFgo Studio1.20.0,just refer to "program application error.png" ,the error shows "programming failed...
I have a sensor device that needs to transmit every so many seconds. I am looking for a code example to run on nRF52-DK that will do this, sleeping inbetween transmissions...
According to the Gazell using the 1MHz spacing for each channels and the DTM using 2MHz spacing.
Then can we use the DTM channel 0 for Gazell channel 2 to test the Frequency...
I am looking for a nordic BLE development board that can do data transfer through the UART. Something like SPP (Serial Port profile).
Here is what I need;
The iOS and...
Hi,
Question regarding blog from Thomas Søderholm ( blog.nordicsemi.com/.../which-technology-should-i-choose-to-connect-my-wearable-device-to-a-phone):
Can't you do...
Keil 5.18a forces me to install "missing Software Pack"
I am trying to set up SDK 11, SD312, with Keil 5.18a, but when I try to load an example from the SDK 11 examples folder...
Hi! I have a nrf51 that act as a central and a beacon that is my peripheral, they connect to each other using is_uuid_present but I can't enable notification using db_discovery...
Hello,
I am currently designing a PCB containing the nRF51822 chip and I am concerned about how I will be able to update the program.
I have 2 main questions :
I...
Hi,
I developed an application with Nrf51822 with some bonding need.
No problem with android or using the dongle, but using iOs systems it happens that after a random attempt...
When I add a GATTC in S110-V6.0.0 ,my GATTS stops working,the NRF Master control panle retern ERROR(0x85):GATT internal ERROR Error(0x85):GATT ERROR .Can S110-V6.0.0 run GATTC...
The note on the IoT softdevice says:
"This SoftDevice is a technology prototype only. Therefore, it should never be used in production."
Will there ever be a production...
Hi
I know perfectly it is not possible to debug while the softdevice is enable and the Bluetooth is working. When I try to set up a breakpoint under these conditions, the...
hello there i want to communicate nrf51 and nrf52 using i2c protocol. [https://devzone.nordicsemi.com/question/75218/i2c-in-nrf51/?answer=75221#post-id-75221]
from this...
Hi ,
I am working on the heart_rate_collector example code of nrf51-ble-driver_linux_0.5.0.
The program detail of nrf51 as below:
-- sorftdevice : s130_nrf51_1.0...
Good morning,
I have designed a prototype based on nRF51822 device. Now, I want to program it with a demo software and I have the Ulink-me tool instead of Segger. From Keil...
