Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi! I am trying to use the Power Profiler app on my Windows computer, I have used it on another Windows computer, and it worked fine. Now, when I try to open the PP app, it...
I’m working on a project trying to characterize the range (given a certain transmitter and environment) on the BLE 1 mbps PHY. I’m using a few nRF52840 dongles to do this...
Hi,
I am evaluating nRF5340 audio dk with CS47L63 DSP. My goal is to find out the MCU processing consumption for LC3 codec what is MCU processing power left for the application...
Hi,
I am writing a program that sends numbers counting up sequentially from my dev board to my phone on 500ms intervals. I used the ble_app_uart example as my base. I am...
Hi all,
I trying to use test-harness v2.6 raspi and nRF52840dk to test commissioning. The result is always failure, and the error is timeout
The firmware DK flash is build...
I have a red pulsating light on the dongle.
dmesg shows it is being detected, on Ubuntu 22.04
[203496.636885] usb 3-3.1: USB disconnect, device number 40 [203508.682046...
Hello,
I have a nrf5340 and pc based on Windows OS. I want to transmit information from 5340 to pc at a speed of 300kbps. Here are my two plans:
Using BLE protocol...
Hi all ,
I had my code working on nRF connect 1.6.0 and now had to upgrade it to work with nRF connect 2.1.2.
I read the migration guide for nRF connect 1.x.x to 2.x.x...
I have tested sending NUS data from nRF52832 to laptop (Windows 10 + Intel core i5), but Windows app doesn’t received all NUS data. But When I tested sending NUS data from...
Hello,
I have downloaded the app for linux from here: https://www.nordicsemi.com/Products/Development-tools/nRF-Connect-for-desktop/Download?lang=en#infotabs
After downloading...
Hi,
I do have a question about the ble_app_uart for central device. Now it is set to make connection with the periheral based on the UUID. I can't find where in the software...
Hi,
I am writing a program that receives a command from a phone using the BLE UART example. The program can count up or down depending on the command. On every count, I...
Hi,
i'm developing an application that uses scan response.
AFAIK sd_ble_gap_tx_power_set is used to set the advertising tx power (BLE_GAP_TX_POWER_ROLE_ADV).
Is the...
Hello,
I am sunning trying to build the hello world sample as mentioned here:
For this project I am working on ubuntu(VM 22.04.1)
I have followed all the steps as mentioned...
