I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hi,
We have a custom nRF5340 board with an nPM1300-QEAA-R7 (QFN32). On two assembled boards the PMIC behaves identically:
Power side works: it ACKs at 0x6B and the BUCKs...
We are currently working with a system that is using both and external flash and the HW WDG from the NRF5340.
Recently we are facing the issue, that we cannot re-flash the...
Hi Nordic Support,
We are using an nRF54LM20 DK, PCA10184 hardware revision 0.7.0, for automated side-channel analysis (SCA) testing.
Our requirement is to repeatedly...
Hi,
We are having issues with getting the output power of +23dBm when using the nRF9160 DK in CW mode.
We use the following command:
AT%XRFTEST=1,1,20,8470,23,1,4,0...
Hello,
I want to program and debug a custom board using my nRF52840 DK (PCA10056 v3.0.3) as the programmer, through the Debug out connector P19. Before I order the cable...
Hi,
We're moving a USB product from an FTDI bridge (FTDI's own VID/PID) to native USB on the
nRF52840, and need to settle its USB identity before release.
Setup...
I was running into issues with issuing the AT#XRESET command for a PPP/CMUX configuration. In an attempt to make the setup as robust as possible we found that the 9151 stopped...
Hi,
We are planning to use nRF Connect SDK Bare Metal (nrf-bm) v2.0.1 but would like to know which toolchain should be used alongside it?
https://nrfconnectdocs.nordicsemi...
We are particularly interested in the following frequency ranges:
2400–2483.5 MHz
2483.5–2522 MHz
2522–2800 MHz
Higher out-of-band frequencies
Could you provide...
My original project contains scheduler mechanism based on nRF5_SDK_17.0.2_d674dde\components\libraries\scheduler\app_scheduler.c. In ncs bare metal v2.0.1, I find the correspond...
So now I have the firmware revision mfw_nrf93m1_1.5.0, updated from 1.4.1 through FOTA. Meanwhile, I tried nRF Connect on nRF93M1 and I have some questions.
1. Most of cellular...
Hello,
I have some trouble to identify my custom nrf52832 board in the VSCODE.
To program the board I am using nrf52840dk, and connect it to my board as follows:
...
Hi,
I have two questions regarding NB-IoT NTN support on the nRF9151 SMA DK:
Does the nRF9151 SMA DK support transmission of 1.25 kHz NPRACH with the currently available...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
