HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello, I've been trying to start few blank projects on sdk 2.6.1 and I noticed that some configurations stop the console output including CONFIG_I2C=y.
I even tried the...
Hello, I am looking for a way to debug firmware that includes MCUBOOT. There seem to be quite some questions in regards to same problem with no real resolution. I am using...
Hi,
I am new to the NRF boards and I want to include the cJSON library into my project code. I am going to get some data from another device using in the cJSON format and...
Hi,
I have used nRF Connect for very long time, and have just upgraded to v5.0.1. The software seems to use a sandbox tech and restores nrfutil.exe to its default version...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
Hello,
In our project we are using FLASH 2GBIT SPI/QUAD W25N02KVZEIR external flash together with nrf5340. I have made the flash definitions on v2.6.0\zephyr\boards\arm...
Hello,
I am trying to bring up a MBN52832 Bluetooth Low Energy Module supplied by Murata that uses the nRF52832 chip. The BT module is connected to the MCU(STM32F427) via...
Hi,
We are working on nrf5340 board with NS and TF-M setup and we have SDK v2.7.0
We need to have a flash partition to store the some secure data may be a size of 4KB...
The sidebar does not load, this is version v2024.7.13.
I uninstalled it and installed it again as an admin, but it still did not load.
Sometimes it loads for a split second...
I am using a custom board with a nRF52832 (inside a BMD-300 from ublox) that I can't seem to get to a lower power state. The lowest I've been able to get is 2.2mA even using...
Hi,
I'm developing an application on the nRF9160DK with custom firmware for both the nRF52840 as well as the nRF9160 on the board, using VSCode with the nRF Connect extension...
Hi,
I am working on an application with ncs 2.5.0 that is based on a combination of the central_uart example and the hci_lpuart as I'm trying to pass data around between...
Hello,
My goal is to read out UICR address 0x10001080UL from command line / MCUMGR.
How to acheive that?
I have tried and successfully compiled ran these mcumgr handler...
