I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi,
I have a project in which I'm using the nRF52840 with OpenThread and the device is configured as an MTD to minimize power usage. I have recently updated my nRF Connect...
Hi All, I am getting build errors for a project. Project specifics below: - nRF52832 (custom board) - NCS v2.6.0 - Custom board files and other configuration files attached...
My application is running on a nRF9160 using NCS v1.7.0 and modem FW 1.3.0. Sometimes, when our device is in an area with bad LTE coverage, I believe we're overflowing some...
Hi there,
I am using the NRF52840DK development board as a learing experience. I have used the EXCERCISE8 on the Nordic learning program and created a SPI driver for a simple...
Hi all, I am observing some strange behaviour on my two nRF52840 devices. They are running NCS v2.1.0 (Zephyr 3.1.99), one as central and peripheral, one as peripheral only...
Hi,
I am trying to build the pc-ble-driver library from source following the readme instructions ( https://github.com/NordicSemiconductor/pc-ble-driver ) on my Windows...
Hi,
MCU: nrf52840
SDK: nRF5_SDK_17.1.0_ddde560
I am facing such an issue, sometimes after the device's OTA success, and then I would like to upgrade to another version...
Hi. I'm on a relatively old ryzen-5 windows 11 PC and I get 30 FPS when recording power with Power Profiler version 4.0.0 and 2 FPS when recording with newer versions (4.1...
Dear Nordic support team,
I cannot enable the Nordic specific HCI command to enable the HCI survey, I always get the following error with NCS v2.6.1:
For information...
Hi,
I am using nRF7002 DK to develop MQTT + I2C sensor. The following are my steps
1. use samples/net/mqtt as the base architecture, everything running well ( I don't...
Hi
From the past few days, I have been trying to perform FOTA with BLE using external QSPI flash. However, I'm unsure if I'm creating the proper files and adding the correct...
Hello, I'm starting to study MCUboot with the intention of implementing firmware upgrades in a product. I'm currently working with the nrf5340dk eval board. As far as I understand...
Hello, I am porting my projects from NCS v 2 . 6 .0 to v 2 . 7 .0 and I am defaulting my builds with sysbuild enabled .
I have a project that has FLASH enabled but doesn...
If you run the exercise 1 code as-is (with the lines from the course materials added) it will run out of sockets and fail within a few button 2 presses. The problem is that...
