Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Hi,
I try to create a one-button minimal "smart watch" based on a small nRF52840 module (register button press) and a second nRF52840 'central station' (receiving and converting...
hi there i hope you are doing fine and best of your health. actually i am developing the custom app to communicate with nrf 52840 soc device through bluetooth, which is working...
I am using PCA10056 3.0.2 dk for my application
when search for schematics of this version board I am getting 1.0.x https://docs.nordicsemi.com/bundle/ug_nrf52840_dk/page...
Hello everyone,
I'm looking for some advice on a slightly offbeat topic related to the Nordic SDK.
I'd like to modify the Makefile of one of the SDK examples so that it...
Hi there!
I am trying to make an application that plays an audio sample to a BLE speaker (another nRF5340 running as headset) where the audio sample is in memory. I have...
Hello,
I am writing to inquire about an issue occurring on our custom board.
Ideally, we should print the logs from the device to identify the exact cause, but since that...
Hi everyone!
I have been developing an application for some time and everything has been running smoothly, until recently testing it and finding out some inaccuracies. ...
This library ( https://github.com/NordicSemiconductor/pc-ble-driver-js ) is pretty outdated, and the linked installation instructions are in an archived repository.
I...
I have a chip that I need to read from connected via SPIM. As one might expected, I have a FIFO I need to read from and a data ready interrupt to trigger the read. As an added...
Hi
I'm wondering if I can build a Bluetooth Mesh network for up to 3500 devices. I researched the BLE Mesh standard and theoretically the protocol can create a mesh with...
Hello,
I'm trying to test if my device BLE5 is working properly. I have an nrf52840 pcb and i using the ble_app_blink_pca example. When used the example as is with an BLE4...
Good day! I want to use Fat FS to connect to a micro SD Card on the Xiao BLE board. Is it possible to configure the board without the help of the expansion module? The main...
Hi
I'm trying to add to my Linux board (RPI4 CM) a cellular connectivity and I thought about using nRF9160 SiP because it's a product I've already used and it's low cost...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
