I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
We are using the NORA-B126-00B module on our custom board, and the first time we flashed it with a simple LED blink example, it worked fine. However, after erasing the...
Hi,
I'm looking at the watchdog behavior in mcuboot during DFU. Here are the watchdog-related configs I've set:
and here are a few things I've noticed:
- Even though...
hello, When I switched from the NCSv3.0.0 version to the NCSv3.2.1 version, I encountered the following compilation issue. How should I eliminate this "Error 1 (Ignored)"...
Background: Our tests on SDK 2.5.0 showed that it was possible to maintain a Bluetooth connection at a distance of approximately 180 meters with the following initial advertising...
i am performing DFU process b/w nrf54l15 and nrf connect mobile_app ( Android ) and i am sniffing the it using nrf54840 soc and the bord is nrf21540dk in Wireshark i know...
Hi,
I am currently working with 2 nrf54L15-DK and a seperate 4 antenna array.
For my tests i run a 2x2 antenna config with preferred peer set to 1 and 4.
I was now...
I just got the board, installed the nRF connect sw. Then installed the J-link, connected the board, power it on and run the quick guide, but it searches and doesn't find anything...
I've been using PPK2 to test our work for maybe around 3 years. it's always been steady and stable and can run for several days without problem. Mostly I'm using the PPK2...
I'm running the nrf5340_audio_dk and using version 2.6.0-rc1. When connecting one NRF5430 as headset to another NRF5340 gateway, running BIS mode everything works fine. But...
Hi,
We've been working on an IoT device that uses an nRF52840 in a pre-approved module from Moko. We are getting ready for a commercial launch in 2026, but I am very confused...
I have noticed that the dts file includes the configuration for arduinio_spi, along with the corresponding pins associated with spi4. However, I am unsure about how to utilize...
The Bluetooth 6.0 Channel Sounding feature supports multi-antenna functionality. The nRF54L15-DK development board is currently single-antenna. Is there any official documentation...
Hello,
I am wondering how I can enable APPROTECT through UICR with a TFM project. Using ncs2.6.0 and nrf5340. My project makes use of TFM to separate secure and non-secure...
Hello,
I am experiencing an issue with the I2S interface on my nRF5340 DK while using the nRF5340 Audio Unicast Server application with the nRF Connect SDK v3.1.0. I am...
