nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
I would like to use NFC on my Thingy:53 to send data or at least a word, how do I set it up? I haven't found any code anywhere.
Thank you in advance
Kind regards...
Hello,
We have been using a custom device based on the NRF9160 SIP with a HTTPs connection for tracking animals and are planning on makeing changes to CoAPs and upgradeing...
Hi Nordic Team,
I have developed a custom board using the nRF9151 controller. I am testing the GNSS sample from nRF Connect SDK v3.0.0 . When I flash and run the firmware...
I have a PPK2 on hand.
Here is what happened:
1. When I first connected it to my Windows 11 PC, the Power Profiler app in nRF Connect for Desktop detected the device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi.
Developing PAwR in project, I have some Question.
before Asking, My Project Structure is below.
1 Gateway (Advertiser) - Node1 (Scanner)
- Node2 (Scanner)
-...
Hello,
I'd like to send/receive data over UART using the expansion board connector of my Thingy:91 X (pins 0.18 & 0.19 as RX/TX). With SB8&9 separated (to isolate pins...
Hi,
I was able to purchase a commercially available 30cm ribbon cable to connect from the nRF54L15 DK to a custom board for programming. I later realized the DK documentation...
Hello,
I have custom hardware using an nPM1300 and nRF52840, and I am having trouble getting the nPM1300 to work as described in its documentation. I have a button connected...
I am trying to write a low level driver for the TWIM system in a nrf52840 and cannot seem to get the hardware to transfer the TX data out of memory. For many reasons, I do...
I am working on project with nrf54l15dk/nrf54l15, and the project runs on cpuapp without utilizing flpr. So, I decided to release the allocated section of flpr on rram_controller...
I'm seeing an issue where nrf91 SLM, running as an AT modem over UART, sometimes chokes on XSEND command and doesn't respond until the host (nrf54) sends another AT command...
i got the following code from here: https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/zephyr/kernel/services/timing/timers.html , and am using version 3.1.1 of the SDK
...
Hello, I am currently trying to use kmu to store a series of derived keys. My current systems derives AES keys and attempts to store it into KMU. As psa_key_derivation_output_key...
Hi,
in ncs3.1.1 peripheral_uart sample after disable the uart init and gpio_config, the nrf54l05 can achieve the low power state,but the avg Idle current was about 5uA,seens...
