This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
In the product specification of nPM1100, for fixed 500mA charging limit, ISET should be connected to VSYS. In the USB-configuration (Configuration 3) ISET is connected to...
Hi:
We want to test the nrf7002 WIFI performance based on the nrf7002 PDK.Do we have relevant test firmware?
We noticed that the sdk document of V2.1.2 has a description...
hi.
I have a firmware using standard GATT, now im implementing the mesh layer.
Im using SDK 17.0.2 + MESH 5.0.0. (im not using the new sdk connect because it is very difficult...
I'm moving from NRF9160DK to a custom board, where it has no UART. I plan to just use RTT for debugging messages.
However, I found if I delete the section which defines...
Hi,
I build secure_bootloader_ble_s132_pca10040_debug example (SDK17.1) on SES 6.30.
The only modification to the project is excluding SEGGER_RTT_Syscalls_SES.c.
...
It is possible to addressing nodes using MAC address of the device in Thread network?
In topology: PC <-> Border router <-> Thread mesh nodes
which IPv6 (Mesh-Local EID...
Hello
I'm new to the nrf platform and wanted to try out the I2C functionality of my nrf5340 DK. The only example I could find was the Fujitsu MB85RC256V FRAM I2C example...
Hi,
We are nearing production stage of our project, and are looking at programming on a large scale. Using the nRF9160 we need to program the latest modem firmware along...
I have a broadcaster and a central device. The broadcaster beacons data every 60sec and goes to sleep, a configuration I have considered for minimal power consumption. Now...
During tests with a "User controlled PLMN selector with Access Technology '6F60'" one device stuck in a curious state:
nRF9160 SICA B0A mfw v1.3.3 CAT-M1, PSM: PTAU 24h...
Hi Nordic community:
Can we configure nRF52840 to support a 1.3 V VIO?
I see from the datasheet, after the internal regulator, what supplies to the chip is actually...
Getting an error from mcumgr and I'm not sure where I should start debugging this.
My environment:
nRF Connect version 2.1.0 Board: nrf52840 DK and nrf52832 DK Host: MacOS...
Hello,
I'm developing with nRF5280-DK, using Zephyr-OS with mbedtls for the cryptography, and I need to have DES and 3DES enabled by default.
I tried to set in the prj...
Hi,
In a ble_app_uart example I have problems to send long packets if the Android smartphone only accepts MTU sizes of 20 bytes. I'm using the nRF5_SDK_17.1.0, the S132...
Hi,
Failed to reset CS47L63 when swapping the role,
if use the configuration like this:
[ { "nrf5340_audio_dk_snr": 1050140236, "nrf5340_audio_dk_dev": "headset", "channel...
