Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hi,
I reviewed the PCA10121 schematic for using SPI4 pins to connect to Semtech SX1262. Since SPI4 bus also connected to SD card and DSP. I checked to see if SPI0..3 pins...
In my application, we regularly transmit a stream of notifications from a Peripheral Server to a Central Client. The general strategy for this is to enqueue a packet, and...
Hello in my app I based it on the BLE UART example and have it pretty much up and running but I need to be able to send multiple messages from the Central to the Peripheral...
I am tring to update the DK bootloader by entering the maintenance mode by pressing the reset button while plugging in the DK, but the board does not show on my PC
any help...
Hi,
I do have Zephyr's logging configured using RTT for debugging messages and in general this works.
Sadly when reflashing (via SWD) the RTT stops working and I have...
Hello,
We are using nrf52832 and SDK15.3 in our product, which sends about 7.4K bytes data every second to an Android phone.
4 ble devices are connected to the phone and...
Hi experts,
I habe a following issue. First I have tried to use nrfx_twi driver. There was any data send over I2C... So I have written own driver using the Datasheet and...
We are trying to send a large message via a BLE characteristic and to do that we have broken up the message payload into smaller fragments and calling bt_gatt_notify() repeatedly...
hi：
I use ble_app_uart routine, test the receiving rate, use the mobile phone to send data, 52832 receive the fastest can only be 10KB.
In addition, when the interval...
Hi
Compile the cli sample into a hex file,Download it to the board, read the hex file through the nRF Connect for Desktop Programmer tool, and then convert it to the bin...
Description:
Facing an issue with k_sleep() function misbehaving after few months due to the internal counter ticks crossed uint32_max values. Simulated the same by hardcoding...
Hi,
we are currently using NCS 2.0.2 on nRF52840 .
Is it possible to disable uart1 via pinctrl or another library during runtime and re-configure the rx/tx as gpios? ...
Hi,
I have met some problems while building the environment of pc-ble-driver-py. Error occurs in this command. The error points that I do not install git, but I have installed...
Hi, I'm new to nrf development. I was able to successfully install the SDK and toolchain using the toolchain manager. But when I'm trying to build a sample project "Blinky...
