Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi,
Not sure if this is the correct place to ask...
My code is crashing after a spi write function.
It is probally obvious to someone here, i think i fell into that...
I'm attempting to merge 3 HEX files into one using the Merghex command. The "BinaryImage access" error appears, see the screenshot below.
I've tried this several times with...
Hi,
I'm porting my SSD1333 (Solomon IC for OLED displays) code driver to Zephyr OS drivers for ease of use along with LVGL (going from `< nrfx_spim.h>` to `<drivers/spi...
I want to transfer a bunch of data over the virtual com port to a PC using the USB port on the nrf5340. I'm using the CDC ACM sample: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
why
AT%XRFTEST=1,1,14,7880,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7930,23,1,4,0,0,0,0,0,0 AT%XRFTEST=1,1,14,7980,23,1,4,0,0,0,0,0,0
returns ERROR but e.g.
AT%XRFTEST...
We are trying to see if it is possible to detect a vibration using the ADXL362 accelerometer on the Thing:91. We have it setup to to trigger on motion, but we need to be able...
Dear all
I following the example here , over the air one, and get it basically working, thanks for the tutorial.
Now I have a few questions:
1. It looks like it always...
Hi
I am studying Matter, my setup is
chip-tool : chip-tool-android_armv7l.apk v2.1.0
OTBR : raspberry pi 3b + RCP( PCA10059 )
board : nRF52840-DK(PCA10056)
sample...
My pairing is working and shown as bonded on Android, but when the DK is reset, the bond is no longer valid.
In studying saving of bond information, I find references to...
Hi,
I am learning Matter. I have some questions:
Where can I get the resources, especially official resources, to study Matter?
What is the use of the Service discovery...
Hi,
We are developing our product using nrf5340. Currently, we are using NCS v1.9.1 for development. We need to give UART to test our Board for Certain conditions by using...
I have been learning to use the nrf52840DK for some time now, though I would consider myself still a beginner. Anyway, something has gone wrong with the kit and I am not sure...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
