Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hi, I wanted to change at runtime the iSerialNumber exposed by USB descriptor. As Kenneth suggested ( link ), the solution has been to override the weak function in usb_descriptor...
#define GPIO_SPEC_AND_COMMA(button_or_led) GPIO_DT_SPEC_GET(button_or_led, gpios),
I find this code in the buttons and led .c file
I tried finding what is does , but...
Hi!
We use the following approach:
If the pin is configured using nrf_gpio_cfg_input we read the pin value via nrf_gpio_pin_read;
If the pin is configured using...
Hi,
I wanted to store a simple integer (the "serial number") by using Setting subsystem of nRF Connect SDK 1.8.0. Settings is based on the internal flash of device (nRF5340...
Trying out Nrf5 sdk v17.1 with SES 6.32 and opened up an ANT+ example `ant\ant_debug\d52\s212\ses`
Tried to build, 50% compiled successfully, but i get repeated errors on...
We use nrf52833, and the SDK is 17.1.0. We have the following questions about gzll: 1. How to count packets_num and timeouts_num in Packets Statistics? timeouts_num Where...
Hello,
I am trying to send a large file through BLE from an nRF52811 to a Raspberry Pi 4. File size is about 77 kilobytes.
Here is BLE setup on the nRF side:
Custom...
Using the DM, in the discovery_complete callback, after finding two CCC handles from 2 custom UUID's, I can subscribe to only one of the two, the other fails with EALREADY...
Hi,
I am not sure where to go next, so looking for some debug help.
Setup : I am using the 9160DK - the 52840 is being used as an ANT+ receiver, where it forwards on UARTE...
I am working with the AWS IoT sample on the nRF9160 development kit using Nrf connect 1.8.0. I am testing the disconnection behavior by removing the sim card after connection...
Hello to all :-)
i am not sure if this is an Hardware-topic, but i want to know the possibilities how to can
use and configure the nRF5340 (where can i find a detailled...
Following some previous posts on how to get the Bootloader version from the application, mainly this post: devzone.nordicsemi.com/.../221367
I noticed that initially the...
I am working on a power-sensitive project and am interested in minimizing system quiescent currents as much as possible. The project is intended to run off of a coin cell...
