I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I am currently struggling with a problem where Im trying to implement the internal fds module which always leads to hard faults as follows:
There is probably something...
Hi,
I read the link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrfx/drivers/twis/driver.html and updated periodic_sync example as attached below.
But I...
We are trying to compare the accuracy of received coordinates and satellites using GNSS firmware on two devices: 1) nRF9160 DK with external antenna; 2) Our custom board with...
Hi,
Mesh SDK: v5
Using nRF 528232
I had implemented the Low Power Node example from the SDK and found that the current it consumed using a 1000mAh 3.7V battery was around...
Hello,
Scenario:
2x nRF52833 - One set as PTX and the second PRX. PTX is connected to my PC via UART. Both boards are initialized with ESB_PROTOCOL_ESB_DPL.
I want to...
Hello,
I am using nrf5 SDK for thread SDK for development of my thread based product. Product is already developed just have to integrate dfu in it. Few months back when...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. It works fine. How do I view the logs? I installed the toolchain and Segger on Windows. I am following this doc...
I use my own programs and routines nrf5_ SDK_ 17.0.2\examples\ble_ peripheral\ble_ app_ hrs\pca10040\s132\arm5_ no_ packs Product Bluetooth broadcast cannot be searched Android...
Hi,
Using the Peripheral LBS sample, is there a way to add advertising data to use both the UUID and name?
I assume this is to be configured in the bt_data ad declaration...
I am using UART on the Fanstel BLG840F to communicate from the 9160 to the 52840. So far I have successfully been able to communicate from the 52840 to the 9160 but have not...
Here we go again .... I did read many posts in this forum but did not find an answer.
We need to CE test a small Bluetooth HID keyboard for a special use case. Our test...
I am running into the exact same issue described here: https://devzone.nordicsemi.com/f/nordic-q-a/53693/how-to-flash-application-after-dfu-bootloader/217434#217434 Basically...
Hi, Nordic Team
I’m getting started trying to use both MCUboot and NSIB for 2-stage secure boot on nRF9160, and use SEGGER as developed tool. I enable NSIB via “Configue...
Near as I can tell from v1.7 of the product specification, these two parts have the same footprint & pin-out because they're both aQFN packages (as indicated by the "QI")...
