I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Unable to write to flash memory using direct memory access functions like sd_flash_page_erase & sd_flash_write (nrf52840 nrf SDK 17.1.0) Also attached application and bootloader...
Hello, I'm experiencing an issue with communication between the nRF52840 and nRF9160 on the Thingy platform using the connectivity bridge. I successfully established communication...
Support,
Due to the limitations described in the referenced previous ticket, I am unable to successfully discover a service and its characteristics because of a hard fault...
I am struggling with the same requirement as this ticket :
ie receive from a UARTE without knowing in advance how many rx bytes to expect. This is typical for exchanging...
I'm running the nrf5340_audio application on the nRF5340 Audio DK and have a UART wired to TP60 and TP61. As long as I have USB (onboard j-link) or my Segger j-link connected...
We used to specify BOARD and BOARD_ROOT at the cmake level, but so far attempts to do the same using sysbuild did not succeeded. Is it still possible or should we rely on...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1024, please.
It is not very clear by reading the assembly code...
Hello,
Is it possible to know what is the cause of this assert : app: ZBOSS assertion in file: 24, line: 1050, please.
It is not very clear by reading the assembly code...
Recently the source control icon (git extension) in the activity bar in vs code shows more than changes in code.
As can be seen here the icon adds up the changes in...
AWS IoT example not working with v2.6.1 SDK with nRF7002 DK but works fine with v2.5.2 SDK.
*** Booting nRF Connect SDK v3.5.99-ncs1-1 *** [00:00:00.249,725] <inf> aws_iot_sample...
Hello all,
I use nRF52840 for my custom board. I set P1.11 & P1.12 as UART_RX & UART_TX. But these two pins can not work.
Here is my nrf52840dk_nrf52840.overlay.
Here...
In the Wi-Fi throughput sample code folder the main.c file has virtually nothing in it, just a few boilerplate lines and a main() with only two lines of code that set the...
Hi,
I have a nRF9160-DK (PCA10090, 1.0.0, 2020.50) that I am trying to flash with the Modem Shell using the Quick Start app on a M1 Max MacBook Pro, running macOS 14.5....
Hello,
I am evaluating the nRF5340 for a potential BLE audio application. I was able to program the kit following the instructions and using the build script (or through...
Hi there,
The nRF54L15 has only 32 GPIOs, which severely limits its use in many applications. I wanted to use it instead of the nRF52840 in future products, but the lack...