I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I'm trying to link a static library that provided by others to my own project. I followed the steps in this post ( https://devzone.nordicsemi.com/f/nordic-q-a/39338...
Hi all
I'm using nrf52805 soc, softdevice s112 , sdk version 17.0.2 and nrf connect mobile app for my project development. I can connect and disconnect the nrf52 device...
Hi,
I am using P0.10 GPIO of nRF52840 (QFN package) as an output for driving a transmission circuit with an 8MHz digital signal.
According to the datasheet this pin is...
Hi team, I'm using Mesh in my project. Using this thread as a reference, I tried to decrease the data throughput and experiment to see if devices could communicate with each...
hello,
i want to know if is possible have Multilink, ble Uart and relay together? it is for make an a type of Mesh network of 4 devices with a BW of 1Mbps (see the image...
Hi
I'm testing the SLM application in nRF Connect SDK ver 1.3.1 on nRF9160 PDK ver 0.8.2 using the LTE Link Monitor v3.5.0
Giving the following commands, the UART stop...
hello ,
i am working on recieving data from sensor using nrf52832 with time and data right now i am getting time that is set by me my problem is i have to set time automatically...
Here is an issue I am having when using MQTT in a poor (RSRP < 15) LTE signal environment
Condition:
nRF Connect SDK v1.3
modem firmware v1.2
TLS Socket is configured...
I've worked through the Custom BLE Service example ( https://github.com/NordicPlayground/nRF5x-custom-ble-service-tutorial ) and I'm attempting to port it to C++ to form the...
Hi,
I need to write a linker (ld) script for our nRF52 application. Essentially I need to combine the linker script that we already use with the scripts that exist in the...
trying to build a long range coded phy broadcast/scanning application. as I know zephyr doesn't support that so we have to include nordic link layer based on this post
https...
Hello all,
i am using ble_app_uart example.I add the line
in the begining of the main function. All the ble connection works, but putty shows strange characters...
I am having a bit of trouble getting high enough data throughput for my application so I have a few questions regarding it.
Can running the spi/other peripherals affect...
Hi，
I tried to build a BLE sniffer environment. And it works well to capture the LE secure connection air packet after Eable Secure Connections debug mode （uses the debug...
