Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi.
I am developing on a custom board using nRF82820 / SDK 17.0.2.
A project was created by modifying examples \ble_peripheral\ble_app_gls.
There is no project for...
Hi,
I am trying to use nRF connect desktop with nRF52840 dongle.
But, in Bluetooth Low Energy app, when I select connected dongle in the drop down list, it always return...
Hello,
My sensor based on nRF52833 will have soldered non-rechargeable battery and it will be potted in resin compound to insure waterproofing.
I wonder, what if for some...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device based on nRF52840 with nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b...
Hi,
I'm currently trying to load my firmware into some custom nRF52832 boards. It seems that several of them have been locked up after previously working. Other boards...
Hi, we recently purchased a Nordic Thingy 52 module and were trying to program it. We used a J-link recorder and a cable for the connection between the J-link and the Thingy...
I have installed CMSIS according to this
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v14.1.0%2Fsdk_config.html
documentation. After...
Hi Team,
One of my application needs the UART driver in both Interrupt and DMA mode for more data bytes transfer. No need of timeout operation or polling mode.
Can any...
Hello Nordic;
I use SDK 17.0.2 and gls example . We know for security in pairing, considered a password which that is randomly generated in SoftDevice and sent to UART....
I am having problems loading an existing project that I successfully built and ran in the past.
I open IDE from nRF Connect > Toolchain Manager > Open IDE
The SES opens...
Hi,
Our Nordic app is doing BLE<->SPI communication.
All works fine when running in debug mode with SEGGER IDE.
Once we run without the debugger running, the SPI transmits...
Any idea why I need to send write enable twice, without reading the status in between, to get the write latch set?
It doesn't work this way, but if I change "#if 0"...
Hi,
I'm using nrf52840 on a custom board and have a sensor connected over the pins P0.9 and P0.10
which are NFC pins that have been converted to GPIO by using macro (CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
which hex file shall i install for an LTE application ?
It is basically step 7 of this tutorial: infocenter.nordicsemi.com/index.jsp
I wanna have a LTE application...
I am trying to start developing on my nRF52833 DK using Segger embedded studios, but my board does not show up as a mounted device on my laptop (echoed by the fact that Segger...
