Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
Hi, I'm using nRF Mesh App to provision more than 5 devices for vendor specific models other than on/off model. My purpose is to send some data instead of on/off the light...
Hi all
I am using a nRF52840 with SDK 15.3.0 and s140_nrf52_6.1.1 soft device.
My application is a multi-peripheral device that has a common service, each peripheral can...
Hi
I'm really new to this, forgive me it's a stupid question. I'm using the nRF52 DK from Nordic.
I started with the "Developing with SEGGER Embedded Studio", but when...
In the user manual of nrf52832 it is said that ram[n].power are retained registers in sleep mode and that depending on the settings.
One or more RAM sections can be retained...
Dear Nordic DevZone Team, With ARM cortex M4, it is possible to go into deep sleep mode. In the Nordic nRF52832 which uses M4, it is configured for BLE advertising. I would...
Hi
I read nRF52840 - LPCOMP information on datasheet and SDK.
It shows VHYST value is 35mV (typ.) in datasheet page 191 and 50mV (typ.) in SDK - nrf_lpcomp.h.
which...
Hello,
In addition to previous ticket I have further queries. I have a stringent requirement for reduction of Current consumption.
https://devzone.nordicsemi.com/support...
Hi, I've got a quick question here about using the GPIOTE driver in tandem with the GPIO HAL . For simplicity's sake, I'm using an in-house library that gives me high-level...
I have been encountering a rather latent bug in a product that we are developing. It consists of a custom nRF52832 board, that is connected to an nRF52-DK via ESB, and the...
Hi
In eddystone when we connect the beacon in connectable mode then it start non connectable advertising automatically without disconnect, same time we can change parameter...
How to send some data from light_switch_server node to light_switch_client node in the mesh sdk examples of the new version mesh sdk 3.1.0?
I basically want to send data...
Hi everyone,
I made a custom pcb and it has nrf52810. I want to flash it using by nrf52840 DK.
This is my connection ;
My Board(nRF52810) -> nRF52840-DK
SWDIO -> SH_SWDIO...
I built this ( devzone.nordicsemi.com/.../Nordic_2D00_Thingy52_2D00_FW_2D00_master.zip) Nordic Thingy SES project and downloaded the generated hex file in Nordic Thingy. Now...
Hello,
I tried to build the mesh sdk in all way.
Please help me or send me the sdk set-up which is without error.
I tried by sdk15.3.0, sdk15.2.0 and mesh sdk. Try...
Hi,
I am having problems with using BLE along with gpiote and ppi for measuring the delay between two waveforms and sending the delay between them to an app using bluetooth...
