I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hi,
I'm using the S132 v3 and wonder about the impact of DLE on scheduling.
In the chapter on Scheduling in the softdevive specification is writen that multiple peripherals...
I would like to setup the just released RasPI demo using the Nordic-Thingy52-Nodejs repo
I don't have a dongle, but 4 PDK 52840 boards and 2 Thingys.
Can I still use 1...
I found that blindly configuring all GPIO pins can stop the LFXO and RTC counter. I am reporting this as: something to be aware of, not obvious to everyone. Not a question...
I am testing the nRF52832 in Rigado BMD-301 module. I am able to get to ~40uA when advertising ,UART enabled but not used and all other peripherals disabled. But as soon as...
I connect to my BLE peripheral device using NRF connect app. While in connection, if I switch my phone's bluetooth off and turn it back again and then try to connect to my...
Hi!
I'm using the nrf52 on custom prototype boards and the official development boards. We are using the ADC to read analog values and encountered unexpected behavior related...
Starting notification and then writing 0x01 to the control point
does not cause the Buttonless DFU to enter boot mode. LED #1
remains on.
Run time trace show:
APP...
The Problem ist the continuous sending of Byte-Arrays with spi and fixed sample rate.
Strategie:
Send Array-List with XFER triggered by Timer (every 3ms) and auto increment...
Hello,
I bought Nrf 52832 breakout board .
Actually i want to measure the current consumption of chip as we want to use it.
While advertising 26 bytes it consume really...
I have questions about the HCI packet format
With the start packet, the Ack number in the header section = 000
What should it be filled in the data packet and...
I'm implementing an I2C communication and I need to set an interruption every time the sensor sets the interrupt pin to 0. I've been checking some other posts from devzone...
Hello,
I am currently trying to power profile all aspects of the nRF52840, which includes the CryptoCell 310. The instructions say "
Testing
Test the CryptoCell Example...
I tried to use Timer2 as counter with event and interrupt. event is working. interrupt not.
<pre><code>
timer_count_cfg.mode = NRF_TIMER_MODE_COUNTER;
err_code = nrf_drv_timer_init...
s132_nrf52_5.0.0-3.alpha_softdevice.hex (/attachment/26a9916e1af8c97bcba7185035bd7b31)Hi, I am starting to work on NFC and Bluetooth pairing for the nrf52 and i tried to compile...
