I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello,
as part of my tries to use xip on nrf52840, I found that using the entire program on the external flash is impossible due to Errata 216 .
I check the FICR for my...
Hello,
I am needing to use two separate SPI masters, but I'm running out of pins. Are all of the pins compatible with SPI or are there some I should avoid. I'm thinking...
Hi all,
I have an application that is pretty simple. One master that needs to stream small payloads (sub 32 byte) to a receiving device. The payload is a fixed size and...
Question: nRF9161 Getting the high accuracy oscillator (HFXO) outside and sync with other nrf chips?
Basically I want to get the Clock Signal outside on a Pin, is it an...
We have 1 central device and 4 peripheral devices in which one of the peripheral is mobile device if we connect both mobile and other peripheral devices(nrf52840) the central...
I am testing an nRF9160 devkit with a TMP117 I2C sensor. My current goal is to read values from its registers.
My current code uses the function i2c_reg_read_byte to read...
Hi,
I've just received a nRF52840 DK and I'm trying to build and flash the blinky sample on it but the build failed continuously.
I also tried with other sample like the...
I want to convert raw hex bytes to utf8 format. The nRF5 SDK supported this with help of ble_srv_ascii_to_utf8() api. Is there something similar api available with nRF Connect...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0 ]
I am planning to set up the system as...
Good night,
I am doing the course "nRF Connect SDK Fundamentals" to learn about Zephir integration with nRF52840.
I am developing a RTOS solution based on the RAKWireless...
Hi,
I have an application that each 30 minutes connects to AWS, sends some data and then disconnects and goes to sleep. I have based my aplication on the asset_tracker...
I am trying to use the nrf5340 audio DK for the first time using one of the sample blink codes. I keep getting an error when first creating an application by copying the sample...
Hi everyone,
I'm a bit lost with the nordic documentation. Here : https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/applications/serial_lte_modem/doc/MQTT_AT_commands...
we have two questions about dfu recover operation on coex_ble&wifi example. because its flash size is so big that it could not be reduced under 500kB. so, we thought that...
Hi team, We are working on integrating TFT LCD touch display with Nordic SoC. We have existing driver support for ILI9341. A display that we checked had ILI9341v LCD driver...