I've developed my BLE application that is based on nRF518822 and softdevice S110 v.8.0.0.
I've defined 6 services (4 with 2 characteritics each and 2 with 1 characteristic...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Hi,
I've reliably implemented a Software Serial library on the nRF52832 using GPIOTE and nrf_delay_us to sample the 8 bits. I tried making this work more efficiently using...
Hi
Is it possible to use the 54dk for programming of our new board with the nRF54L15 running on 1.8V?
Is the voltage configurable on the 54 dk?
Best regards
Peer
I am using nRF Connect SDK (NCS) v2.9.0 for a Matter project.
Currently, the Manual Pairing Code generated is 21 digits long. I need to change this output to be 11 digits...
We follow the youtube video: www.youtube.com/watch
to add battery charging and fuel gauging to our nRF52832 Series project.
It works, but after we enable
CONFIG_PM_DEVICE...
Hi nordic team
I am working with the Nordic nRF5340 SoC using Zephyr RTOS .
Hardware
External QSPI flash:
MX25R6435F
QSPI configuration (DeviceTree):
...
Hardware: nRF9151 DK Modem firmware: mfw_nrf91x1_2.0.4 Carrier: Verizon (PLMN 311480), Band 13 Antenna: External Problem The modem continuously reselects between two cells...
Hi Nordic team,
In the context of adapting the software for our custom PCB I need to make some changes in some devicetree nodes for the net core. Therefore I wanted to add...
I designed a circuit using the NRF54 to connect via Bluetooth and control several peripherals. I program the chip using the Debug Out of the NRF54L15 DK . The code can be...
Just bringing this to your attention. This has been an issue since at least 2.6.1, and appears to still be a problem in main.
static void connected(struct bt_conn...
Hi, What specific steps must be followed to modify the charging current (BCHGISET) of the nPM1304? The information I found says to disable the charger first (set BCHGENABLECLR...
I am evaluating the monitor mode debugging support in nRF Connect SDK with nRF52840-DK and an arbitrary BLE sample (like peripheral_uart). My SDK/toolchain version is 3.1...
Summary
We are running on an nRF54L15 and receiving continuous NMEA output from a GNSS module over UART using UART ASYNC. After some time (30 minutes to hours) of normal...
Hello,
I am getting an error with the modem_info_params_get() function when I try to get the modem parameters. I am currently using SDK 3.2.0 with the FW MFW_nRF9151-NTN_v1...
