I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
I have a chip that I need to read from connected via SPIM. As one might expected, I have a FIFO I need to read from and a data ready interrupt to trigger the read. As an added...
Hi
I'm wondering if I can build a Bluetooth Mesh network for up to 3500 devices. I researched the BLE Mesh standard and theoretically the protocol can create a mesh with...
Hello,
I'm trying to test if my device BLE5 is working properly. I have an nrf52840 pcb and i using the ble_app_blink_pca example. When used the example as is with an BLE4...
Good day! I want to use Fat FS to connect to a micro SD Card on the Xiao BLE board. Is it possible to configure the board without the help of the expansion module? The main...
Hi
I'm trying to add to my Linux board (RPI4 CM) a cellular connectivity and I thought about using nRF9160 SiP because it's a product I've already used and it's low cost...
Hi
Spotify 128 kbps aac stream is about 16 bytes per ms. Ble should support 31 bytes per packet.
So can I stream 16 bytes ms over lte m to nrf 9160 then via uart to...
Good morning!
I hope you will forgive my trivial question but I am a beginner. I don't quite understand the partition structure presented in the "NVS" example. Using the...
Hi,
A veteran of nRF5 SDK but new to NCS.
I tried to run tx_rx_non_blocking example from the latest (2.6.1) NCS SDK, but can't get it to run (nR52840DK)
It seem...
Hello, I recently set up an nRF52840 with the nRF7002 evaluation kit using the WiFi station sample. However, during the build process, I noticed that it consumes a significant...
Hi,
I'm integrating an external SPI flash W25Q32 with the nRF52840 using the NOR FLASH driver, but it's not functioning properly as the MCU log indicates an MPU error. ...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it. ( developer.nordicsemi.com/.....
Hi All!
I have a question, i am using nrf52833Dk as an extended advertiser and nrf52840 dongle / 2nd nrf52833Dk as a scanner using the BLE desktop App (nrf connect for desktop...
I am not able to send 25 array packets each second. array size is 244 bytes I am reading the sensor data continuosly and every 40 ms i am sending the data to bluetooth using...
Hello,
I am on a development team utilizing Nordic Board NRF52DK to connect to a custom NRF52832-based board/external device via debug out on the Nordic Board NRF52DK, the...
Hi,
I'm experimenting with an Acconeer XM126 board which has an nRF52840 processor (and an Acconeer A121 chip) and a Bluetooth antenna (and an RF antenna too). I'm deploying...
