Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
Environment: SDK v3.1.1 with a custom board based on the nRF52840.
I wrote a test application that I've been using to verify the hardware on a custom nRF52840 board. I have...
Hi,
We are using an nRF52832 in a bare-metal project. (No SDK)
We have three input channels to the ADC that we wish to use. These must be oversampled. (256x)
To simplify...
Hi guys,
I'm trying to do FOTA updates on my board and I was able so far to download the image but not able to apply it.
I've followed the academy FOTA over WiFi example...
I've got an example code to turn on an LED with a button, it works. When I change it to send an spi command, it doesn't work anymore.
Could you check if you see something...
Using;NRF52832,
SDK17,
Flutter 3.10.5 ,
nordic_dfu : 6.0.1,
iOS 16.5.1
iPhone 14 Pro Max
Using my developer device I can successfully update DFU,
However on...
I flashed the same code to the two nrf5340dk but i get the below output , with out any changes in the example sample code. it gives the serial output every time E: IPC endpoint...
I have installed both sdk 3.0.0 and 3.1.1 but both of them give me the following issue:
Upon building, the error given above shows for some reason but this is not my own...
Hi,Team,
I am currently using the nrf5415 to develop OTA. My NCS version is v3.0.2. Now I have two types of devices: Hub and Terminal. Both of these devices use nrf54l15...
The uart output of nrf52840 dongles is corrupted, including no lines separation, strange characters. for example:
5E0 to 1:00000000148A0C90 [18FF] [UDP:�]�8~~[fdbc:dc24...
I first noticed this when incorrect flags reported by mcumgr when performing network core update
When performing a network core update with CONFIG_SECURE_BOOT_APPCORE enabled...
Hello, I am currently debugging with nRF52833 and nRF5 SDK, and I have a few questions to ask:
I want to time-share the BLE function and the ESB function on a single MCU...
When I2S reads the digital audio sensor, when strat is turned on_ After I2S, the data can be read and recognized normally, but this action takes up the whole CPU occupancy...
Hello Nordic team,
I have a question related to the “nRF5340 Production Programming – Troubleshooting” documentation, specifically the part that says the access port protection...
Per (+) Trouble with nPM1300EK - Nordic Q&A - Nordic DevZone - Nordic DevZone , I've disconnected TWI from the board while doing the battery profiling and that worked successfully...
