Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hello,
We are in pre-production and we need to make 1000 prototypes.
Here is the filter we planned to use : https://www.johansontechnology.com/datasheets/2450FM07A0029...
Hi support team,
Customer needs them for BLE certification though I think those in nRF52840 report are same.
BTW, may I pre-fetch nRF5340's for any future request? ...
Hello,
Have any developers here on the forum had luck with getting the nRF9160 DK working in India?
Our India dev team has looked extensively and has not yet been able...
Hi, dear Nordic.
I tried to build secure_bootloader_ble_S132_pca10040 project in Segger. And it gives me this error message:
cannot find ../../../../../external/micro...
Hi,
I am trying to get my nrf24L01+ to communicate with nrf5340 using the enhanced shock burst sample code. In the sample code there are LOG_INF, LOG_ERR, LOG_DBG commands...
Hello Nordic Team,
We are in production phase, and flashing our modems one by one does not work well. It is too slow process, so we are looking for a solution that can offer...
Hi,
I'm trying to develop a Bluetooth Mesh Network using 3 Thingy52s and one Thingy91 that acts as a gateway to Azure IoT Hub. I saw the sample code LTE BLE Gateway for...
Hi,
I am trying to get the Atmel WINC1500 module to work with the nRF9160DK.
I have read a similar post,
https://devzone.nordicsemi.com/f/nordic-q-a/76640/spi-issue...
Hej!
I am trying to make a circuit / configure my SW for using the nRF5208 to have a small power consumption when not trainsceiving . Basically, I need my setup to have...
Hi! The nPM1100 is advertised specifically as a complementary product to the nRF52 and nRF53 product line. Seeing how the nRF9160 can also operate at 3V, I was wondering why...
Hello, I am working with an nRF52811 and I am trying to get it to send data via UART with a USB connection. I tried using the USB CDC ACM module, but it appears to only work...
Hello,
my application requires a reliable break detection (The serial data input is '0' for longer than the length of a data frame) sent from a peer device on the UART RxD...
I am working on reading and writing data to an external QSPI flash (MX35LF4GE4AD) that has an internal cache mechanism. I have been able to read/write to the flash using standard...
I am currently working on a project developing a USB HID product based on the nRF52840. I have run into an issue regarding USB communication reliability and am seeking the...
