Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
Hi,
In our application, we are using HID to control mobile phone or PC.When users connected our product, it will automatically connect next time.
But our product is battery...
Hi
I am using Zephyr samples (common with the samples found in NCS) to evaluate the advertisement function of nRF52833DK.
I have run these examples:
Bluetooth: Periodic...
Hi,
After updating the FW as shown on the video, LED3 is NOT blinking, trying to connect (LTE).
If I open the terminal window, select the board, and pressing the Reset...
Hi,
We are using the GPS xample for the nRF9160. and are struggling a little with getting the GPS fix.
$GPGGA,001932.00,,,,,0,,99.99,,M,,M,,*6F $GPGLL,,,,,001932.00...
Hello to all the Nordic Jedi knights!
I have a question regarding the PPK2: Is there a way to disable auto-ranging and manually select the measurement range?
I know that...
Hey,
I have a custom board with nRF52833. Sensor is connected to: P0.11 (pin 19) - SCL P1.08 (pin 17) - SDA
with code below I don't get any `NRF_SUCCESS` back.
I saw...
I'm trying to build a new device that I bit, bang the I/O Also others to just have simple signal controls.
Below is the portion of my dts file. The example here is the onewire...
Hi,
I am using nRF52810 (s112 softdevice) with SDk version "17.0.2".
How do I set BLE advertise in continuous mode(if not connected then advertise continuously until it...
Hi
I am trying to declare a custom cluster in zigbee and enable the reporting for some attributes of the cluster, i followed this post to create the custom cluster devzone...
Hi guys,
I'm researching the maximum direct connection distance between two Android phones for transfering small amount of data - which lead me to BLE Coded PHY S8 as a...
Hi,
I m using nRF52840 dongle to setup the nRF5_SDK_17.0.2 .
Besides, the related software and the Segger Embedded Studio are installed.
Occurred Problems :
When...
Dear members,
How can I wake up the system after idle ?
It goes to main loop, but never wakes up if there's a signal from HRM,BSC or B.Power after search time out and...
