Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
I'm working on a BLE peripheral that will connect to both iOS and Android devices. It is important to maintain connection during usage so I consider increasing supervision...
Hi! Are there any existing solutions to send the NRF_LOG output over BLE or to write it straight to a flash/SD-card? If not, would editing the macro's in nrf_log.h be an appropriate...
Hello,
I have a gateway project where I need to receive data from BLE and send on ANT network. As a first step, I took the NUS or ble_app_uart and changed the softdevice...
Dear Members,
I saw ST7735_DC_PIN and ST7735_SS_PIN, which one should I connect to my LCD it has only CS pin ?
ON LCD board ST7735_SCK_PIN 47 --> P1.15 PIN 3 SCK ST7735_MOSI_PIN...
Hello Everyone,
I am using nrf52 dk development board. I'm having a problem when I load my ble_app_uart example . I am getting an error message Error: Flash Download failed...
Hi,
I'm trying to use the nrf52832 as the SPI master to get read/write flash ic MX25L6433FM2I-08G(address - 0x00 to 0xFF).
In loopback case got data but when interfacing...
SDK: nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
I get started with Zigbee Door Lock Example in https://infocenter.nordicsemi.com/topic/sdk_tz_v4.1.0/zigbee_multi_dynamic_door_lock_nus_example...
Hi,
We have ordered nr51822 chips in the past. Recently, we made a new purchase and on programming we have discovered that the FICR register information is different for...
Hi Folks,
I am currently implementing a power down routine onto the nRF52840 SoC and I have some questions regarding the right way to configure to system On sleep mode...
Hi,
Is there an example code which can be used to evaluate libuarte while softdevice enabled? I have tried the individual examples in "nRF5_SDK_17.0.2\examples\peripheral...
Hello,
I would like to know what exactly is doing PM_HANDLER_SEC_DELAY_MS and how can affect to the interoperability.
I saw in the bms example (sdk 15.2) it is set to...
The BLE specification says that the CTE can be a maximum of 160us long. I am trying to set CTE length to 160us, but every time i try to do so, firstly the transmitter stops...
Hi Devzone:
We are using J-link pro to collect trace data from nRF52833 DK board, and we found a rather strange behavior:
The sw interrupts would end on its own without...
Hi,
I'm trying to connect an NRF52840-DK to a MAX30101 Wing board via I2C/TWI. I've set up the TWI Manager to send a message asking the MAX board for its part ID.
This...
