Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
I bought a custom nrf52840 board and I need to program my firmware on this SOC with PCA10056 DK debug output port. in below you can see part of shematic of my custom...
I have some custom models in my mesh application in addition to SIG standard models. As can be seen with interactive_pyaci script when i read the composition data of my device...
Hi guys.
I'm working with a nRF52832 custom board.
In my case my board communicates with the LIS3DH through i2c protocol. In the other hand based on LIS3DH datasheet the...
Sir
about the
while(1)
{
sd_app_event_wait(); //stay here until a interrupt or connection occurs...
}
During the time that there is not a interrupt and no connections...
Hi,
I've recently switched some prototype code from using MQTT to a custom UDP-based protocol. What I noticed is that if I have the unit sleep for longer periods of time...
Is it allowed and possible to change the configuration of one pin from input to output chararacteristic (and back) during the normal work flow. I need this possibility for...
Howdy,
To achieve the lowest possible power consumption on the nrf9160, it is noted that it is necessary to disable the UARTs that are not used, when in sleep mode. However...
I'm unable to write a softdevice to my nrf52840, can someone please point me in the right direction?
I was able to program the board just fine using nRFGo Studio, but I...
Hi, I am using Adafruit BLE sniffer with nRF51822 v2 firmware and I am sniffing BLE packets in Wireshark. I can see my devices advertisement data when my device is in the...
Hello,
We are using the nrf connect Android app in order to scan and connect to ble peripherals.
The scan procedure is executed perfectly as we can identify and connect...
Hi In v5 one can advertise in le_coded and then a central can connect off the resulting AUX packet.
For the AUX_CONNECT packet the inter-packet delay is T_MAFS which is...
When I read Objective Product Specification v0.7.1, it seems external pull-up resistors are required.
However, when I use TWIM without them, it works out.
Do I need...
Hi Everyone,
I am using nRF52832 with SDK v14.2 and SD v5.0.0 on a custom chip.
Recently i included DFU support to our application. It turns out that secure bootloader...
Hi, I'm new to nRF52480 and Nordic SDK. It is first time for me when SDK has one big config file sdk_config.h. I started playing with examples (LEDs, serial I2C) and get it...
I am developing a PCB that contains this schematic, I can run the sw code on the nrf52832 and use the pinout, but I can't connect to nrf52832 via ble communication. I think...
