Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
I am attempting to write a routine that monitors the heap in order to track down a memory leak. I've seen similar tools on other platforms and found them quite helpful. To...
Hi,
Previously I have merged spi with ble_app_uart on NRF52832 based ISP1507 test board . It has performed successfully which was enough to carryout the evaluation phase...
Hi. experts, I tested [TC-ACE-1.2] Subscriptions with Test harness, which is UI-Python. I execute it on Docker,./certification-tool/scripts/otbr/otbr _ start.sh; And write...
Hello.
I'm trying to figure out which microcontroller is best for my use case. I need to have as many bluetooth low energy concurrent connections as possible and the device...
After rummaging through the awful and extremely limited documentation relating to external programming using the NRF52840 DK (so I don't have to pay for the $700 scam device...
Greetings
I am trying to use the BLE fundamentals exercise (Lesson 4 exercise 2 solution) to send actual sensor data, that I receive via I2C, to my nrfConnect app.
When...
I have a question about for LE. In my understanding, BT connection must confirm each profile, and it is able to connect same profile that each products have. For example,...
Hi,
I just wander why in the peripheral UART sample for the nRF5340-DK (ncs, SDK 2.7.0), the prj.conf doesn't include the internal capacitor configuration:
prj.conf file...
I realize that Bluetooth is the primary target of these devices these days, but I wanted to try an old tried and true example on the nrf5340. I am rather familiar with esb...
Hi,
When I try nrfsdk/zephyr/sample/bluetooth/periodic_adv_rsp, after changing subevent_interval to 8, I meet following error:
*** Booting nRF Connect SDK v2.7.0-5cb85570ca43...
