Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
Hello,
NB-IoT Dual HARQ and Max TBS size enhancement brought in Rel14 (Cat-NB2): on nRF9160 it was controllable via AT%REL14FEAT, using parameters <NB_dual_harq_support...
Hello,
One question on the Reduced Mobility feature (3GPP Relaxed Monitoring TS36.304 and Nordic-proprietary feature) based on %REDMOB command.
AT manual says :
%REDMOB...
AS-RAI (RAI over Access Stratum ; Rel-14) over LTE-M was available on the nRF9160 via the command AT%REL14FEAT (option <as_rai_support> e.g. AT%REL14FEAT=0,0,0,1,0 to enable...
With the current version of nRF Connect for Desktop I received an error when updating the Toolchain Manager.
I then uninstalled the Toolchain Manager and tried to reinstall...
Hello,
Although my board is not equipped with an external LC filter, I flashed firmware which enables DCDC and this made the chip unresponsive.
Is there any method...
Hey
I'm trying to figure out what is the intetned way of using the tools for configuring a project.
We have the following config files in the following structure:
...
Hello I currently have an error when flashing with j-link on a custom board. The mcu is nRF52833 QDAA and the debugger pin is connected to 4 pins. In VSCODE, CONNECTD DEVICES...
I am working on a pdm microphone INMP621. I am getting the pdm data using nrfx pdm drivers but not sure about the logic which I am implementing to convert pdm to pcm. I read...
Hi,
I'm working with nRF5340 Audio DKs.
I'm able to successfully run the audio example in BIS mode (with gateway and headset devices).
My goal is to open another BT...
Hi, I need a little help with mcuboot.
We want to transfer firmware updates via CAN (MCP2515), which is already implemented. Was we are short of time, and we want to integrate...
We have a design using a nrf5340 with a Renesas Wifi chip, That Renesas chip uses a 1 wire interface for Coexistence
We are using Zephyr 3.5.0 and have tried to follow https...
Hi, I have Adafruit I2S MEMS Microphone Breakout - SPH0645LM4H for getting sound and for driving output via speaker I have tas2x63EVM amplifier. Since the nrf5340 audio dk...
Hi,
We want to have some RF-PHY tests on nRF52840 DK.
Therefore, I need a HEX file to make nRF52840 DK get into direct test mode and communicate with CMW270 with UART...