I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
I'm trying to read the CTS characteristic from a BLE server (an iOS device) and part of the requirement from Apple is that the server and client be paired and bonded before...
Hi Friends,
- kit dev NF52840-DK
- IDE : segger studio IDE
- SDK nRF52 16.0.0
I want to port the nfc_writable_ndef_msg NFC example to freeRTOS.
I use the NFC Tools...
I'm learning that there are issues with the early "engineering versions" of the nRF52840, identified with QIAAAA marking.
Apparently the SPI3 BUS is not fully supported...
Hi,
After some strange behaviour of the DAC4716 chip, I want to try and reset it. The datasheet describes a way to do so over i2c using a specific bit stream. How can this...
I am having a N20 Micro Gear Motor with Encoder, I want to read data of c1 and c2 using GPIO pins. Any specificAPI, method or suggestion for this?
I am using nRF5340 along...
We have an application running on an nRF9160 development board (shortly to be ported to a production board), which listens on a serial link for sensor data, which is then...
Hello,
For network testing, I would like to use the Modem Shell App sample with the Thingy:91.
As suggested in the overlay file, I can disable some features, so the Build...
Hello,
I am attempting to use my nRF52810 (testing with the nRF52 DK) to generate square waves using PWM. Ideally, these square waves would operate at 8 or 16Mhz. So far...
Hi,
When will Nordic Connect SDK 2.1.0 be available? When have Nordic qualified SDK 2.1.0 and when is QDID number available (Host and Controller)?
We are running Zephyr...
Hi,
I am using the sensor_server example to develop our application on top of it. The problem I am facing is that, the model publication state (publish address and publish...
Hi,
I am using sensor server model to build our application on top of it. We want to save juice in the battery as much as possible. In order to that, I must disable bluetooth...
Hi, I'm developing a device based on nrf52840 and SDK for Thread and Zigbee 3.2.0.
I would like to send Route Record command to the coordinator to be able to see the actual...
Hello! We are trying to sign our data using ECDSA ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/crypto/ecdsa/README.html ) , so we can send our...
Hi,
as mentioned in a previous ticket I'm developing a successor to one of our products. One important feature is that we can change pin functions anytime. (output, input...
