Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
While stating debugging mode or normal mode i didn't pair with any devices after advertise duration in RTT viewer
This error raising [ 00> <error> app: Fatal error ]
and...
Hello Nordic community,
We are a software development team. We can directly work on development kits but as a initiative we are trying to buy SOC and do others steps manually...
As described in the brief spec of nRF 21540：
the nRF21540 improves the RX sensitivity by 5 dBm to -100 dBm.
5dBm should be 5dB，you can't make a simple plus/minus equation...
Hi,
I'm doing a Bluetooth test for the nrf52840. However, RF-PHY/TRM-LE/CA/BV-13-C cannot be tested. This means that the instrument does not provide results. The measuring...
Hello,
I want to supply the nRF52832 with a power supply of 2.2Vdc. The uC has to measure an analog voltage between 0 to 2.5V using the internal reference.
Is it possible...
I am trying to set up usb cdc and use the virtual COM port for logging. Please find my code below.
Issue - The LED part of the code works fine but when dongle is connected...
Hi,
I'm testing a prototype with the nRF52840 where I drive a buzzer in the following way:
When I play a signal, I see that the current through the buzzer is about...
Dear everyone,
I'm new to Zigbee and Nordic development. I'm currently working on Zigbee on nrf52833. I must implement a mesh topology to prove self-healing and self-routing...
Hello Nordic team,
I'm looking for some help about Thread creation ... I try to start a Thread when my nrf52840 receive a particular message. This message is sent with BLE...
I am working with the nRF5340 development board. I got the multicore example from the SDK to build without an issue. I then copied the source code and CMake scripts into a...
Trying to get the entire set of v2.0.0 software development tools to install on our Ubuntu 20.04.4 LTS x86_64 system for my nRF9160-DK.
Following the [DevAcademy nRF Connect...
Hi Team,
I am using nRF52810 gpio to power gate (gpio connected to VIN) ADXL362 . But the ADXL362 recommends a switch(SHUTDOWN) as shown below to discharge the capacitors...
Are there any plans for updating the internal CoAP buffer sizes to support 511 OpenThread children? There are two cases where the number of maximum OpenThread children is...
I have an OpenThread application that worked on NCS v1.9.1 and after updating to NCS v2.0.0 (nothing in the source code or kconfig was changed), the application fails to build...
Hi
I need to read the Drive mode of how an output pin has been configured....
I see that there is an API to read pin's Pullup, Direction, Sense, etc configuration.....
